Reading Pneumatic Symbols and Schematics
Learn the ISO 1219 symbol language: how valves are drawn as boxes, what positions and ports mean, how port numbers work, and how to trace a simple circuit.
Why Schematics Matter
A pneumatic machine can have dozens of valves and cylinders behind guards and inside cabinets. The schematic is the map. If you can read it, you can trace where air should go, then go check where it actually goes.
Pneumatic and hydraulic schematics use the same international standard, ISO 1219. Learn it once and you can read both.
The Valve Is a Row of Boxes
The single most important idea: each box is one position the valve can be in.
- The number of boxes = the number of positions
- The lines touching one box (usually the normal box) = the number of ports
- Arrows inside a box show where air flows in that position
- A T shape inside a box means that port is blocked
Valves are named ports/positions. A 5/2 valve has 5 ports and 2 positions. A 3/2 valve has 3 ports and 2 positions.
Reading the Example
- Normal position (right box, spring holds it there): supply 1 → 2, and 4 → 5 exhausts. Port 3 is blocked.
- Shifted position (left box, solenoid energized): supply 1 → 4, and 2 → 3 exhausts. Port 5 is blocked.
Imagine sliding the left box over to line up with the port lines. That’s what happens when the solenoid fires.
Hook port 4 to the cap end and port 2 to the rod end of the cylinder, and you have the most common circuit in pneumatics: energize to extend, de-energize to retract.
Port Numbering (ISO 5599)
Port numbers tell you a port’s job, even when the drawing is cluttered.
| Port | Function |
|---|---|
| 1 | Supply (pressure in) |
| 2, 4 | Working ports (out to the actuator) |
| 3, 5 | Exhaust |
| 12, 14 | Pilot signals: “12” connects 1 to 2, “14” connects 1 to 4 |
Older drawings use letters: P (pressure), A and B (working), R and S or EA/EB (exhaust).
Common Symbols
| Symbol idea | Meaning |
|---|---|
| Circle with a dark triangle pointing out | Compressor (source) |
| Small open circle with a dot | Pressure source connection |
| Open triangle at a port | Exhaust to atmosphere |
| Rectangle with a diagonal line at a valve end | Solenoid actuator |
| Zig-zag at a valve end | Spring return |
| Diamond | Conditioning device (filter, dryer, lubricator) |
| Arrow through a symbol | Adjustable (e.g., regulator, flow control) |
| Rectangle with piston line and rod | Cylinder |
The “Normal” Position
Schematics are drawn with the machine at rest, with power and air applied but nothing actuated. The port lines always attach to the box that represents that state.
Common mistake: reading a schematic as if air is shut off.
Schematics show the at-rest, air-on condition. A spring-return valve in its normal box is still sending air to one side of the cylinder. That cylinder is held under pressure even though nothing is “on.” This is stored energy, and it’s why lockout requires dumping air (Module 6).
Key Takeaway
Boxes are positions, lines are ports, arrows are flow paths, and T’s are blocked ports. Port 1 is supply, 2/4 are working, and 3/5 are exhaust. The drawing shows the machine at rest with air on.
Using the diagram above, answer:
- With the solenoid de-energized, which cylinder port is pressurized? (Port 2 → rod end. The cylinder is held retracted.)
- With the solenoid energized, where does rod-end air go? (Rod end → port 2 → port 3 → exhaust.)
- If the solenoid coil burns out, what will the cylinder do? (Spring returns the valve to normal. The cylinder retracts or stays retracted.)
1. What does a '5/2 valve' mean?
Valves are named ports/positions. A 5/2 valve has five ports and two positions.
2. In ISO 5599 numbering, port 1 is:
Port 1 is supply. Ports 2 and 4 are working ports, and 3 and 5 are exhausts.
3. What does a T symbol inside a valve box mean?
A T inside a box means the port is closed off in that position.
4. Schematics are normally drawn showing the machine:
The drawing shows the at-rest state with air applied, so cylinders may be holding pressure.