Rotary Actuators, Grippers, Air Motors, and Vacuum
Go beyond the cylinder: rack-and-pinion and vane rotary actuators, parallel and angular grippers, air motors, and vacuum pick-up with venturi generators and suction cups, including how to size a cup.
Rotary Actuators
When you need to turn something a fixed angle, such as flipping a part, opening a gate, or turning a valve, use a rotary actuator.
| Type | How it works | Typical rotation | Notes |
|---|---|---|---|
| Rack and pinion | Pistons drive a toothed rack that turns a pinion gear | 90°, 180°, adjustable | Very common on process valves and indexing |
| Vane | Air pushes a vane inside a round chamber | Up to about 270° | Compact; lower torque; sensitive to dirty air |
| Helical / scotch yoke | Linear piston motion converted to rotation | 90° | Scotch yoke gives high torque at the ends of travel, ideal for valves |
Rotary actuators are rated by torque (in·lb or N·m) at a given pressure. Like cylinders, they need cushioning or external stops when rotating heavy loads, because rotating inertia stores a lot of energy.
Grippers
Grippers are the “fingers” of pick-and-place machines and robots.
- Parallel grippers — jaws move straight in and out; good for parts with parallel faces
- Angular grippers — jaws pivot open; cheaper, need more clearance
- Three-jaw grippers — center round parts
Key specs are grip force, stroke, and the jaw length the force is rated at. Force drops as fingers get longer, so always check the maker’s chart.
Fail-Safe Gripping
What happens if air is lost while a part is held? Options include:
- Spring-assisted grippers that hold on air loss
- Check valves that trap air in the gripper
- Mechanical self-locking jaw designs
Choose deliberately. A dropped part over a person or a fixture is a safety problem, not just a quality problem.
Air Motors
Air motors spin continuously, like an electric motor, using vanes or pistons.
- Speed varies with load: free speed with no load drops as torque increases
- They can stall without damage and restart, which electric motors can’t do safely
- Safe in explosive atmospheres and washdown areas because there’s no spark
- Very air-hungry, so they cost a lot to run
You see them in mixers in hazardous areas, hoists, and handheld tools.
Vacuum: Picking with Suction
Vacuum handling lifts parts like cartons, sheets, and glass using suction cups.
Making Vacuum with a Venturi
Most plant vacuum comes from a venturi (vacuum ejector): compressed air rushes through a nozzle, and the fast-moving jet drags air out of a side port, creating vacuum. No moving parts, instant on and off, but it consumes compressed air the entire time it runs. Many ejectors include an air-saving function that shuts off supply once vacuum is reached and only resumes if vacuum decays.
For large, continuous vacuum needs, an electric vacuum pump is usually cheaper to run.
Vacuum Units
Vacuum is often measured in inches of mercury (inHg) below atmosphere. One inHg is about 0.49 psi. A good venturi might pull around 20–25 inHg (roughly 10–12 psi below atmosphere). You can never exceed atmospheric pressure, about 14.7 psi at sea level, as your maximum “push.”
Sizing a Suction Cup
Holding force = vacuum (psi) × cup area (in²), then divide by a safety factor.
Common rules of thumb for safety factor:
- 2 for a horizontal lift (cup on top of the part, lifting straight up)
- 4 for a vertical lift (cup on the side of the part, relying on friction)
Use more when there’s fast motion or a porous or oily surface.
Common mistake: sizing the cup on clean, smooth test parts, then running recycled corrugated cartons.
Porous board and rough surfaces leak air through the material, so vacuum never builds fully. Measure the vacuum actually achieved on production parts, use bellows or foam cups for uneven surfaces, and add a vacuum switch that confirms grip before the robot moves.
Key Takeaway
Rotary actuators turn a fixed angle and are rated in torque. Grippers need a defined fail-safe behavior on air loss. Air motors are spark-free and stall-tolerant but costly to run. Vacuum cups lift with vacuum × area ÷ safety factor, and you should always confirm vacuum before moving the load.
You need to lift a 12 lb flat steel sheet horizontally. The venturi delivers 20 inHg ≈ 9.8 psi. Use a safety factor of 2.
Required theoretical force = 12 × 2 = 24 lbf. Required area = 24 ÷ 9.8 ≈ 2.45 in². Cup diameter = 2 × √(2.45 ÷ π) ≈ 1.77 in.
Using two 1.5-inch cups (≈ 1.77 in² each, 3.53 in² total) gives margin and better balance.
1. Which rotary actuator design gives high torque at the ends of travel, making it popular for valve automation?
Scotch yoke actuators produce peak torque at the start and end of stroke, where valves need it most.
2. What is a key advantage of air motors over electric motors?
Air motors tolerate stalling and suit explosive or washdown areas, but they use a lot of air.
3. How does a venturi vacuum generator make vacuum?
The high-velocity jet entrains surrounding air, lowering pressure at the vacuum port.
4. Why use a larger safety factor for a vertical suction-cup lift?
With the cup on a vertical face, the load hangs on friction, so a higher safety factor (often 4) is used.