Fuel Quality and Combustion Troubleshooting
Recognize water, microbial growth, and air in fuel, bleed a fuel system, read exhaust smoke color, and use exhaust temperatures and cylinder balance to find combustion problems.
The Three Enemies of Fuel
1. Water
Water gets in through condensation in partly empty tanks, leaking deck fills and vents, and contaminated bunkers. It:
- Damages injectors and pumps (water doesn’t lubricate)
- Causes rough running and power loss
- Feeds microbial growth
Drain settling and service tanks and filter bowls regularly. Keep tanks full where practical to reduce condensation.
2. Microbial Growth (“Diesel Bug”)
Bacteria and fungi live at the fuel-water interface and form dark, slimy sludge that clogs filters fast. Signs: rapid filter plugging, black or brown slime in filter bowls, a sulfur or rotten smell.
Control it by removing water, cleaning tanks, and using biocides only as directed.
3. Air
Air in the fuel lines stops a diesel. It enters after running a tank dry, changing filters, or through a loose fitting on the suction side (which leaks air in, not fuel out).
Bleeding the Fuel System
After a filter change or running out of fuel, the system must be bled to remove air. The general approach (always follow the engine manual):
- Fill new filters with clean fuel if the design allows.
- Open the bleed screw on the first filter; pump the hand primer until fuel flows without bubbles; close the screw.
- Repeat at the secondary filter, then at the injection pump.
- If the engine still won’t start, crack the injector line nuts (with eye protection), crank briefly until fuel appears, and retighten.
- Fix the cause of the air leak.
Reading the Smoke
Exhaust color is a fast, useful diagnostic.
| Smoke color | What it usually means | Common causes |
|---|---|---|
| Black / dark gray | Too much fuel for the available air (incomplete combustion) | Overload, dirty air filter, turbocharger problem, faulty injector, wrong timing, fouled hull or propeller |
| Blue | Burning lube oil | Worn rings or liners, worn valve guides, turbo seal leak, overfilled sump |
| White | Unburned fuel or water vapor | Cold engine, low compression, late timing, water in fuel, coolant leak into the cylinder |
A little dark smoke during acceleration or white smoke during a cold start can be normal. Persistent smoke at steady load is not.
Exhaust Temperatures and Cylinder Balance
Many engines have a pyrometer (exhaust temperature sensor) on each cylinder. At a steady load, all cylinders should read close to one another.
| Pattern | Possible cause |
|---|---|
| One cylinder much higher | Dribbling or leaking injector, late injection, leaking exhaust valve |
| One cylinder much lower | Injector not firing or blocked, fuel pump problem, failed sensor |
| All cylinders high | Overload, restricted air intake, turbocharger fouling, high intake air temperature, fouled hull |
| Rising trend over weeks | Gradual turbo or charge air cooler fouling; dirty air filters |
Larger engines also measure firing pressure (Pmax) and compression pressure to diagnose combustion directly.
Common mistake: looking only at today’s exhaust temperatures with no history.
A cylinder 20 °C above the others might be normal for that engine, or it might be a new problem. Log temperatures at the same load every watch. Changes from baseline are what matter.
Key Takeaway
Keep fuel dry, watch for microbial sludge, and bleed air after filter changes or running dry. Black smoke means too much fuel or too little air; blue means oil burning; white means unburned fuel or water. Use cylinder exhaust temperature balance and trends to spot combustion problems early.
A tug’s main engine shows:
- Black smoke under load
- All cylinder exhaust temperatures about 40 °C higher than last month at the same rpm
- Turbo boost pressure lower than normal
What’s the likely problem area? (Air supply. Probably a fouled or damaged turbocharger, a dirty intake filter, or a fouled charge air cooler. Less air means too much fuel for the air available, so all cylinders run hot.)
What might you check outside the engine? (Hull and propeller fouling increase load at the same rpm.)
1. Blue exhaust smoke most likely indicates:
Blue smoke comes from lube oil entering the combustion chamber, from worn rings, guides, or turbo seals.
2. Where does air typically enter a fuel system to cause hard starting?
Suction-side leaks draw air in, and running a tank dry fills lines with air.
3. One cylinder's exhaust temperature is much lower than the others at steady load. A likely cause is:
A cold cylinder usually isn't getting or burning fuel properly. Check the injector, pump, or sensor.
4. What does diesel bug (microbial growth) need to thrive?
Microbes live where water meets fuel. Removing water is the primary control.