Cooling Systems: Raw Water, Fresh Water, and Keel Coolers
Module 3 · Lube Oil and Cooling

Cooling Systems: Raw Water, Fresh Water, and Keel Coolers

Understand closed fresh-water jacket cooling and open sea-water circuits, heat exchangers and keel coolers, raw water pumps and impellers, sea chests and strainers, thermostats, coolant treatment, and sacrificial anodes.

Getting Rid of Heat

Only part of the fuel’s energy turns into shaft power. A large share leaves as heat in the exhaust and cooling water. The cooling system keeps metal temperatures in a safe, steady range: hot enough for efficient combustion, cool enough to protect liners, heads, and oil.


Two Circuits

Most marine diesels use indirect (two-circuit) cooling:

enginejackets + headheatexchangerhot fresh waterthermostatcooled fresh watercirculating pumpexpansion tankCLOSED fresh-water circuitsea cheststrainerraw waterpumpoverboard (wet exhaust or discharge)OPEN sea-water circuit
  • Fresh-water (jacket) circuit: a closed loop of treated coolant circulates through the engine block, liners, and heads. It stays clean, so corrosion and scale are controlled.
  • Sea-water (raw water) circuit: an open loop draws seawater through a sea chest and strainer, pumps it through the heat exchanger (and often oil and charge air coolers), and discharges it overboard. On many small vessels, it’s injected into the wet exhaust to cool it.

Keel Coolers and Box Coolers

Many workboats, tugs, and fishing vessels use keel coolers: tubes or channels mounted outside the hull below the waterline. Engine coolant flows through them and sheds heat directly to the surrounding sea. No raw water pump, strainer, or heat exchanger is needed for the jacket water, which means fewer clogging problems in silty or icy water. Box coolers do the same inside a recessed hull box.

Keel coolers lose efficiency when fouled with marine growth or painted with the wrong coating.


Key Components

ComponentNotes
Sea chest and sea valveHull opening for seawater; valve must be operable (and is a critical watertight boundary)
Sea strainerCatches debris, kelp, jellyfish; check and clean regularly
Raw water pumpOften a flexible rubber impeller pump on small engines; impellers wear and fail if run dry
Heat exchangerTube bundle; seawater in the tubes, coolant around them (or plate types)
ThermostatBypasses the cooler until the engine reaches operating temperature
Expansion tankAllows for coolant expansion; check level here
Sacrificial anodes (zincs)Corrode instead of engine metals; inspect and replace on schedule

Coolant Treatment

Fresh water coolant must be treated with corrosion inhibitors (and antifreeze where needed) per the engine maker. Test regularly for inhibitor concentration, pH, and chlorides. Rising chlorides suggest seawater leaking into the closed circuit through a heat exchanger failure.


Overheating: A Quick Checklist

  1. Raw water flow: Is water coming out of the exhaust or discharge? Is the sea valve open? Is the strainer clogged? Has the impeller failed?
  2. Coolant level: Check the expansion tank (only when safe; never open a hot pressurized cap).
  3. Heat exchanger: Fouled or plugged tubes?
  4. Thermostat: Stuck closed?
  5. Load: Overloaded engine, fouled hull, or wrong propeller?
  6. Keel cooler: Fouling or air trapped in the circuit?
⚠️ Common Pitfall: Running a Dry Impeller

Common mistake: starting the engine with the sea valve closed after maintenance, or with a clogged strainer.

A flexible impeller running dry can be destroyed in seconds, and its broken vanes travel downstream to block the heat exchanger. Check the sea valve and strainer before starting, and confirm water flow immediately after. Carry spare impellers and know how to change one.


Key Takeaway

Most marine engines use a closed fresh-water circuit cooled by an open sea-water circuit through a heat exchanger, or by keel coolers outside the hull. Watch the sea strainer, raw water impeller, anodes, and coolant chemistry. When overheating, check raw water flow first.

🧪 Try It: Engine Overheat Drill

You’re on watch. The main engine’s jacket water temperature alarm sounds, and there’s less water than usual coming out of the wet exhaust.

Write your first three actions. (Example: Reduce load and notify the operator/bridge. Check the sea strainer and sea valve. Check the raw water pump and impeller. Do NOT open the hot expansion tank cap.)

🧠 Knowledge Check

1. In a two-circuit cooling system, which circuit flows through the engine block?

2. What is a keel cooler?

3. Rising chloride levels in the fresh-water coolant suggest:

4. Why are sacrificial anodes (zincs) fitted?