Engine Room Rounds and Watchstanding
Learn how engineers and oilers stand watch: pre-start checks, starting and warm-up, systematic rounds using sight, sound, smell, and touch, keeping the engine log, responding to alarms, and handing over the watch.
The Watch Keeps the Ship Running
Whether it’s a licensed engineer on a cargo ship or a deckhand-engineer on a crabber, someone is responsible for the machinery. Good watchstanding finds small problems before they become breakdowns at sea.
Pre-Start Checks
Before starting a main or generator engine (adapt to your vessel’s checklist):
- Fluid levels: lube oil, coolant expansion tank, reduction gear oil, fuel day tank
- Valves: sea valves open, fuel valves open, exhaust and cooling valves set
- Drains: water drained from fuel filters, air receivers
- Bilges: dry and clean; check for new leaks
- Belts and guards: in place and tight
- Turning gear: disengaged
- Pre-lube: run the pre-lube pump if fitted
- Indicator cocks (on larger engines): blow the engine over on air with cocks open to expel any water or fuel from cylinders, then close them
- Communication: tell the bridge or operator you’re starting
Starting and Warm-Up
After starting, check immediately:
- Oil pressure comes up within seconds
- Raw water discharge is flowing
- No unusual noise, vibration, smoke, or leaks
Let the engine warm up at light load before applying full power. Cold engines wear faster and can seize pistons if loaded hard.
Making Rounds
Rounds are a planned walk through the machinery spaces at a regular interval (often hourly while underway).
- 1 Gauges
Pressures, temps, levels, alarms
- 2 Look
Leaks, drips, smoke, bilge levels
- 3 Listen
Knocks, whines, changes in pitch
- 4 Smell
Hot oil, fuel, electrical burning
- 5 Feel
Temps (carefully) or IR thermometer
- 6 Log
Record readings and actions
What to Check on Each Round
| System | Items |
|---|---|
| Main engine | Lube oil pressure and temperature, jacket water temperature, exhaust temperatures per cylinder, boost pressure, rpm, load |
| Reduction gear | Oil pressure and temperature, sounds |
| Shafting | Stern tube and line bearing temperatures, seal or packing leakage |
| Generators | Voltage, frequency, load (kW), temperatures |
| Fuel | Day tank level, filter differential pressures, separator operation, leaks |
| Cooling | Sea strainer differential or condition, expansion tank levels |
| Bilges | Levels and contents (oil? water? where from?) |
| Steering gear | Hydraulic oil level, leaks, noise |
| Air | Starting air receiver pressure, compressor operation |
The Engine Log
The log is a legal and technical record. Record:
- Readings at set intervals
- Engine starts, stops, and speed changes (often ordered by the bridge)
- Fuel and lube oil soundings and transfers
- Alarms and actions taken
- Maintenance done during the watch
- Unusual events
Write clearly, in ink (or the electronic system), and never alter old entries. Corrections are lined through and initialed.
Responding to Alarms
- Silence the audible alarm and acknowledge it.
- Identify what alarmed and check the actual condition (sensor fault or real problem?).
- Act: reduce load, start a standby pump, switch filters, or stop the engine if needed.
- Inform the chief engineer or the bridge as required.
- Log it.
Some conditions cause automatic shutdown or slowdown, such as low lube oil pressure, overspeed, and high jacket water temperature. Never override a safety shutdown without authorization and a clear understanding of the risk.
Common mistake: an alarm goes off repeatedly for a “known” issue, so the watchkeeper silences it each time without looking.
That one time it’s real, a bearing runs hot or the bilge floods. Every alarm gets checked. If an alarm is truly faulty, repair it or formally report it. Don’t train yourself to ignore it.
Handing Over the Watch
The relieving watchkeeper should not take over until they understand:
- Machinery running and on standby
- Any abnormal conditions or ongoing work
- Orders from the chief and bridge
- Tank levels and transfers in progress
- Any lockouts or isolations in place
Key Takeaway
Do pre-start checks, confirm oil pressure and raw water immediately after starting, and warm up before loading. Make regular rounds using all your senses and compare to normal. Keep a clear log. Investigate every alarm, and hand over the watch completely.
For a vessel or engine you know (or from a video tour), make a one-page round sheet with columns for each hour and rows for at least 12 readings: lube oil pressure, jacket water temperature, exhaust temperatures, gear oil pressure, generator kW, fuel day tank level, bilge level, and so on. Add a column for normal range.
1. What should you check immediately after starting a marine diesel?
Oil pressure must come up quickly, and raw water must flow to prevent overheating and impeller damage.
2. Why open the indicator cocks and blow the engine over on air before starting a large engine?
Liquid in a cylinder can cause hydraulic lock and serious damage when the engine starts.
3. How should an incorrect engine log entry be corrected?
The log is a legal record. Corrections are lined through and initialed, never erased.
4. An alarm keeps going off for a known minor issue. What should you do?
Every alarm must be investigated. Faulty alarms should be fixed, not ignored.