Torque, Speed, and Power
Understand the three quantities every drivetrain trades between, calculate horsepower from torque and rpm, and see how speed ratios multiply torque through belts, chains, and gearboxes.
What a Drivetrain Does
Electric motors usually spin fast (often around 1,750 or 3,500 rpm on 60 Hz power) with modest torque. Most machines need the opposite: slow speed with high torque to move a conveyor, turn a mixer, or drive a roll.
The drivetrain connects the two, changing speed and torque along the way.
- 1 Motor
1,750 rpm, low torque
- 2 Belt drive
First speed reduction
- 3 Gearbox
Big reduction, big torque
- 4 Coupling
Joins shafts, absorbs misalignment
- 5 Chain drive
Final reduction
- 6 Head shaft
Turns the conveyor on bearings
This course covers each of those parts in turn.
The Three Quantities
| Quantity | What it is | Common units |
|---|---|---|
| Torque | Twisting force | lb-ft, lb-in, N·m |
| Speed | How fast a shaft turns | rpm |
| Power | Rate of doing work: torque × speed | horsepower (hp), kilowatts (kW) |
The Horsepower Formula
hp = torque (lb-ft) × rpm ÷ 5,252
Or, rearranged to find torque:
torque (lb-ft) = hp × 5,252 ÷ rpm
In metric: kW = torque (N·m) × rpm ÷ 9,550. Also, 1 hp ≈ 0.746 kW.
Worked Example
A 10 hp motor runs at 1,750 rpm. Its full-load torque is:
10 × 5,252 ÷ 1,750 ≈ 30 lb-ft
Ratios: Trading Speed for Torque
When a drive reduces speed, it multiplies torque by about the same ratio (minus losses). Power stays roughly the same going in and out.
Ratio = driver speed ÷ driven speed
For belts and chains, the ratio comes from sizes:
- Belt: ratio ≈ driven sheave diameter ÷ driver sheave diameter
- Chain or gears: ratio = driven teeth ÷ driver teeth
Continuing the Example
That 30 lb-ft motor drives a 10:1 gearbox:
| Speed | Torque | |
|---|---|---|
| Gearbox input | 1,750 rpm | 30 lb-ft |
| Gearbox output (ideal) | 175 rpm | 300 lb-ft |
| Output at 95% efficiency | 175 rpm | ≈ 285 lb-ft |
Every component downstream of a reduction must handle the higher torque. That’s why output shafts, keys, and couplings are much larger than the motor’s.
Efficiency and Losses
No drive is perfect. Losses become heat.
| Drive | Typical efficiency (approx.) |
|---|---|
| Synchronous (toothed) belt | ~97–98% |
| Roller chain, well lubricated | ~97–98% |
| V-belt, properly tensioned | ~93–96%, dropping if it slips |
| Helical or bevel gear stage | ~97–98% per stage |
| Worm gear | Wide range, roughly 50–90%, lower at high ratios |
A hot gearbox or a squealing belt is power you paid for being turned into heat.
Common mistake: a conveyor keeps tripping on overload, so someone installs a bigger motor.
Now the motor can deliver more torque than the gearbox, chain, and shafts were designed for. The next jam breaks a shaft or a gear instead of tripping a breaker. Find out why the load increased (a seized bearing, a dragging belt, product buildup) before changing the drive’s power.
Key Takeaway
hp = torque × rpm ÷ 5,252. Speed reductions multiply torque by the ratio, so parts get bigger downstream. Efficiency losses turn into heat, which is why worm gears and slipping belts run hot. Fix the cause of an overload before adding power.
A 5 hp, 1,750 rpm motor drives a 4-inch sheave belted to a 12-inch sheave on a gearbox with a 15:1 ratio.
- Motor torque? 5 × 5,252 ÷ 1,750 ≈ 15 lb-ft
- Belt ratio? 12 ÷ 4 = 3:1, so gearbox input ≈ 583 rpm and ≈ 45 lb-ft
- Gearbox output (ignoring losses)? 583 ÷ 15 ≈ 39 rpm; 45 × 15 ≈ 675 lb-ft
That output shaft sees 45 times the motor torque.
1. What is the full-load torque of a 20 hp motor at 1,750 rpm?
Torque = 20 × 5,252 ÷ 1,750 ≈ 60 lb-ft.
2. A 20-tooth sprocket drives a 60-tooth sprocket. What happens to speed and torque?
The ratio is 60 ÷ 20 = 3:1. Speed is divided by 3 and torque multiplied by about 3.
3. Why are gearbox output shafts larger than input shafts?
Reducing speed multiplies torque, so the output side must be stronger.
4. Which drive type typically has the lowest efficiency?
Worm gears rely on sliding contact, so efficiency can be quite low, especially at high ratios.