Bearing Types and Bearing Numbers
Module 2 · Bearings

Bearing Types and Bearing Numbers

Identify ball, cylindrical, spherical, and tapered roller bearings and mounted units, understand radial and thrust loads, decode a bearing number like 6205-2RS, and see how L10 life works.

What a Bearing Does

A bearing supports a rotating shaft, carries its loads, and keeps friction low. Every motor, pump, fan, gearbox, and conveyor pulley depends on them, and bearing failure is one of the most common causes of unplanned downtime.

boreouter ringrolling elements (balls)cage (separator)inner ringradial loadaxial (thrust) loadalong the shaft

Loads come in two directions:

  • Radial load: perpendicular to the shaft, such as belt tension or the weight of a roll
  • Axial (thrust) load: along the shaft, such as a helical gear’s push or a pump impeller’s thrust

Different bearing types handle these differently.


Rolling Bearing Types

TypeLoadsStrengthsCommon uses
Deep groove ballModerate radial, some thrust both waysFast, quiet, cheapElectric motors, fans, small conveyors
Angular contact ballCombined radial + high thrust one wayPrecision, high speedPumps, spindles; often mounted in pairs
Cylindrical rollerVery high radial, little or no thrustHigh radial capacity; allows axial floatMotors, gearboxes, rolls
Spherical rollerVery high radial, moderate thrustSelf-aligning for shaft deflectionPaper machine rolls, crushers, fans, conveyors
Tapered rollerHigh radial + high thrust one wayAdjustable preload; mounted in pairsGearboxes, wheel hubs
Needle rollerHigh radial in a small spaceCompactGearbox shafts, universal joints
Thrust bearingsAxial onlyPure thrustVertical shafts, screw jacks

Plain bearings (bushings and sleeve bearings) have no rolling elements. The shaft slides on a lubricated surface. They handle shock well and are used in large turbines, compressors, and slow, heavy, or dirty applications.

Mounted Bearings

Most conveyor and fan shafts use mounted bearing units: a bearing pre-installed in a cast or steel housing.

  • Pillow block: base parallel to the shaft, bolts down to a surface
  • Flange unit: 2-, 3-, or 4-bolt flange that mounts to a wall
  • Take-up unit: slides in a frame to tension a conveyor belt

Inserts lock to the shaft with set screws, an eccentric locking collar, or a tapered adapter sleeve.


Decoding a Bearing Number

Standard metric bearings follow a common numbering logic. Let’s decode 6205-2RS:

PartMeaning
6Bearing type: deep groove ball
2Dimension series: light (0 = extra light, 3 = medium)
05Bore code: 05 × 5 = 25 mm
-2RSRubber seals on both sides (suffix styles vary by maker)

Bore Codes

CodeBore
0010 mm
0112 mm
0215 mm
0317 mm
04 and upCode × 5 (e.g., 08 = 40 mm)

Common Suffixes

Suffix (common examples)Meaning
Z / ZZ or 2ZMetal shield on one or both sides
RS / 2RSRubber contact seal on one or both sides
C3Internal clearance larger than normal, common in electric motors and hot applications
KTapered bore (for adapter sleeves)

Suffix codes differ among manufacturers. When in doubt, use the maker’s catalog or interchange guide.

Other type digits: 1 and 2 often indicate self-aligning ball bearings, N/NU cylindrical roller, 22xxx/23xxx spherical roller, 3xxxx tapered roller, and 7xxx angular contact.


Bearing Life: L10

Bearing catalogs list L10 life: the number of revolutions (or hours) that 90% of a group of identical bearings will reach or exceed under a given load before showing fatigue. Ten percent will fail sooner.

L10 = (C ÷ P)ᵖ × 1,000,000 revolutions

  • C = dynamic load rating (from the catalog)
  • P = actual equivalent load
  • p = 3 for ball bearings, 10/3 for roller bearings

The exponent is the key insight: double the load on a ball bearing and its life drops to one eighth. Over-tensioned belts and misaligned couplings kill bearings fast.

In the real world, most bearings never reach fatigue life. They fail early from lubrication, contamination, or installation problems, which is the next lesson.

⚠️ Common Pitfall: Ignoring the C3

Common mistake: replacing a motor’s 6309-2Z-C3 with a plain 6309-2Z because it was on the shelf.

The C3 clearance allows for the inner ring expanding as the motor heats up. Without it, the bearing can lose its internal clearance, run hot, and fail early. Match the entire number, suffixes included.


Key Takeaway

Choose bearings by load direction and size: ball for speed, cylindrical for radial capacity, spherical for misalignment, tapered for combined loads. Decode the number: type, series, bore code, suffixes. L10 life falls with the cube of load for ball bearings, so overloading is costly.

🧪 Try It: Decode These
  1. 6008-ZZ → deep groove ball, extra-light series, bore 08 × 5 = 40 mm, shields both sides.
  2. 6302-2RS → deep groove ball, medium series, bore code 02 = 15 mm, sealed both sides.
  3. A ball bearing runs at half its original load. How does its L10 life change? (1 ÷ 0.5)³ = 8 times longer.
🧠 Knowledge Check

1. What is the bore of a 6206 bearing?

2. Which bearing type is self-aligning and used where shafts deflect, such as on paper machine rolls?

3. If the load on a ball bearing doubles, its L10 life becomes:

4. What does the C3 suffix indicate?