Shafts, Keys, Bushings, and Fasteners
Learn how power gets from a shaft into a sheave or sprocket: keys and keyways, set screws, taper-lock and QD bushings, bolt grades, proper torquing, thread lockers, and how to read a broken shaft.
Connecting Parts to Shafts
Torque has to cross from a shaft into a hub (a sheave, sprocket, gear, or coupling) without slipping. The usual tools are keys, set screws, and tapered bushings.
Keys
- Square keys are most common. As a rough guide, key width is about one quarter of the shaft diameter (standard tables set exact sizes).
- The key must fit snugly on its sides. A loose key rocks back and forth, hammers the keyway, and eventually shears or “wallows out” the slot.
- Keys are deliberately the weak link: better to shear a cheap key than crack a shaft.
- Use key stock of the right material. Don’t grab any piece of steel bar.
Set Screws
Set screws stop a hub from sliding along the shaft. A typical arrangement puts one screw over the key and a second at about 90°.
- Use cup-point screws; they bite into the shaft.
- Torque them to spec.
- Many plants use thread locker on set screws because vibration loosens them.
Tapered Bushings
Many sheaves and sprockets mount with a split tapered bushing, such as QD or Taper-Lock styles. Tightening the bolts draws the tapered bushing into the hub, squeezing the bushing onto the shaft.
Advantages:
- One hub fits many shaft sizes (just change the bushing)
- Grips the whole shaft circumference, so there’s less fretting
- Easy removal using the jacking holes
Installation tips:
- Clean the tapers; don’t lubricate them unless the manufacturer says to, because oil changes the clamping force.
- Tighten bolts evenly and alternately to the specified torque.
- Don’t close the gap between bushing and hub flange completely on QD-style bushings; a gap is normal.
Fasteners and Torque
Bolt Grades
| Marking | Grade | Typical use |
|---|---|---|
| No radial lines | SAE Grade 2 | Light duty, non-critical |
| 3 radial lines | SAE Grade 5 | General machinery |
| 6 radial lines | SAE Grade 8 | High-strength, heavily loaded joints |
| 8.8 on head | Metric class 8.8 | Roughly comparable to Grade 5 |
| 10.9 on head | Metric class 10.9 | Roughly comparable to Grade 8 |
Replace with the same grade or better. A hardware-store Grade 2 bolt in a Grade 8 hole is a failure waiting to happen.
Why Torque Matters
A bolt works like a stiff spring. Tightening stretches it slightly, creating clamp force. Too little clamp and the joint slips, loosens, and fatigues. Too much and the bolt yields or the threads strip.
- Use a calibrated torque wrench and the manufacturer’s spec.
- Torque values assume a thread condition (dry, oiled, or with thread locker). Lubricating threads raises clamp force at the same wrench reading.
- Tighten bolt patterns in a star (crisscross) sequence, in steps.
Thread Lockers
| Type | Strength | Removal |
|---|---|---|
| Medium (often blue) | Removable | Hand tools |
| High (often red) | Permanent | Needs heat to remove |
| Wicking (often green) | Penetrates pre-assembled fasteners | Varies |
Colors vary by brand, so always read the label.
Reading a Broken Shaft
Most shaft failures are fatigue: a small crack grows a bit each revolution until the remaining metal can’t hold.
- Beach marks (curved ripple lines) on the fracture face show where the crack grew slowly.
- The rough, final fracture zone shows where it finally snapped. A small final zone means low stress over a long time; a large one means high overload.
- Cracks usually start at stress raisers: keyway ends, sharp shoulders, and corrosion pits.
Common mistake: a keyway has worn oversized, so someone stuffs in shim stock or peens the key to make it tight.
It’ll loosen again within weeks, and the hammering spreads the damage to the shaft. Repair properly: cut a new keyway at 90° (if design allows), use a stepped key, sleeve the hub, or replace the part.
Key Takeaway
Keys carry torque and are the designed weak link. Set screws locate the hub but don’t carry torque. Tapered bushings clamp evenly and remove easily. Match bolt grade, use a torque wrench, and tighten in a star pattern. Fatigue fractures start at stress raisers like keyway ends.
Find a sheave or sprocket on a machine (locked out, guard removed by an authorized person). Check:
- Is it keyed, bushed, or both?
- Is the key snug, or can you see wear or fretting (reddish-brown rust powder)?
- Are the set screws present and tight?
- If it’s a bushing, are the bolts tight and is the gap even?
- What grade are the bolts?
1. What carries the torque in a keyed connection?
The key's sides transmit torque. The set screw keeps the hub from sliding along the shaft.
2. A bolt head has six radial lines. What grade is it?
Six radial lines mark an SAE Grade 8 bolt; three lines mark Grade 5.
3. Why should you avoid oiling bolt threads when the torque spec assumes dry threads?
Less friction means more of the wrench torque becomes bolt stretch, so clamp force goes up.
4. On a fatigue fracture, what do beach marks show?
Beach marks record the crack's step-by-step growth before final fracture.