Glossary and Course Review
Review the vocabulary and formulas of mechanical power transmission, walk a complete drivetrain inspection, and test yourself across the whole course.
The Whole Drivetrain
- M1 Motor + shaft
hp, torque, keys, bushings
- M3 Belt / chain
Tension, alignment, wear
- M4 Gearbox
Service factor, oil, breathers
- M4 Coupling
Type, gap, inspection
- M5 Alignment
Soft foot, shims, laser
- M2 Bearings
Numbers, mounting, failures
- M6 Reliability
Lube, monitoring, guarding
Glossary
| Term | Meaning |
|---|---|
| AGMA | American Gear Manufacturers Association; publishes gear ratings and service factors |
| Bar sag | Indicator bracket droop that skews bottom readings |
| Brinelling | Raceway dents from impact or improper mounting force |
| C3 | Bearing suffix: greater-than-normal internal clearance |
| Elongation | Chain “stretch” from pin and bushing wear |
| Fluting | Washboard raceway damage from electrical current |
| L10 life | Life that 90% of identical bearings reach or exceed |
| Matched set | Belts made to equal length for multi-belt drives |
| Mil | One thousandth of an inch (0.001 in) |
| Offset / angular misalignment | Displaced vs. angled shaft centerlines |
| P-F interval | Time from detectable defect to functional failure |
| Pitch | Distance between chain pins or sprocket/belt teeth |
| QD / Taper-Lock | Common tapered bushing styles |
| Service factor | Multiplier on load to size for real conditions |
| Sheave | A grooved pulley for V-belts |
| Soft foot | A machine foot that doesn’t sit flat |
| Spalling | Flaking of raceway surface from fatigue |
| Synchronous belt | Toothed belt that doesn’t slip |
| Thermal growth | Machine dimension change between cold and hot |
Formulas to Remember
| What | Formula |
|---|---|
| Horsepower | hp = torque (lb-ft) × rpm ÷ 5,252 |
| Speed ratio | Driver speed ÷ driven speed = driven teeth (or diameter) ÷ driver teeth (or diameter) |
| Output torque | Input torque × ratio × efficiency |
| Bearing bore (codes 04+) | Bore code × 5 mm |
| Ball bearing L10 | (C ÷ P)³ × 1,000,000 revolutions |
| Belt deflection | Span (in) × 1/64 |
| Chain elongation | (Measured − nominal) ÷ nominal × 100 |
| Required gearbox rating | Load × service factor |
| Rim offset | Indicator reading ÷ 2 |
Choose one motor-driven machine with a belt or chain and a gearbox. With it locked out and guards removed by an authorized person, complete a one-page report:
- Nameplates: motor hp and rpm; gearbox ratio. Calculate output torque.
- Belts or chain: type and size; tension or slack; sheave or sprocket wear; alignment.
- Gearbox: oil level for the mounting position, oil condition, breather type, leaks.
- Coupling: type, condition, signs of misalignment (dust, heat, wear).
- Bearings: numbers (if visible), greasing method, temperature trend.
- Guarding: is every nip point and rotating part guarded?
- Recommendations: ranked by risk.
1. A 15 hp motor at 1,750 rpm drives a 20:1 gearbox at 95% efficiency. What is the approximate output torque?
Motor torque ≈ 15 × 5,252 ÷ 1,750 ≈ 45 lb-ft. Output ≈ 45 × 20 × 0.95 ≈ 855 lb-ft.
2. What is the bore of a 6212 bearing?
Bore code 12 × 5 = 60 mm.
3. A chain and its sprockets are both worn. What should you replace?
A new chain on worn sprockets wears quickly and can jump teeth. Replace them together.
4. Which should be corrected before precision shaft alignment?
Soft foot and pipe strain distort the machine and make alignment readings unreliable.
5. Glazed V-belt sidewalls and a squeal at startup point to:
Slip heats and glazes the sidewalls and causes squeal. Check tension and sheave wear.
6. Washboard marks across a VFD motor's bearing raceway suggest which fix?
Fluting comes from electrical discharge through the bearing. Grounding rings or insulated bearings stop the current.