The Corrugator, Part 1: Wet End and Single Facer
Module 2 · The Corrugator

The Corrugator, Part 1: Wet End and Single Facer

Walk the wet end of a corrugator — roll stands, splicers, preheaters, the single facer, and the bridge — and learn how starch adhesive forms the bond.

The Machine That Makes the Board

A corrugator is a continuous line — often 100 meters or more long — that turns rolls of linerboard and medium into flat sheets of corrugated board. A modern corrugator can run at 300+ meters per minute and make board for hundreds of different orders in a single shift.

The line has two halves:

  • Wet end: unwinds paper, conditions it, forms the flutes, and glues the first liner on.
  • Dry end: glues the second liner, cures the bond, cools the board, and cuts it into sheets.
WET ENDDRY ENDmediumlinerpreheaterssingle facerbridgeinside linergluedouble backerhot plates + coolingslit/scoreknifestackerboard travel

This lesson covers the wet end. The next lesson covers the dry end.


1. Roll Stands and Splicers

Each paper — medium, single-face liner, and double-backer liner — feeds from a roll stand holding two rolls. When the running roll nears its end, an automatic splicer joins the new roll to the running web at full speed, so the corrugator never stops for a roll change.

Order changes often also mean paper changes (a different liner weight or color), which the splicer handles as well.

2. Preheaters

Paper is wrapped around large steam-heated preheater drums. Preheating:

  • Brings the paper to the right temperature for the starch to gel quickly
  • Drives off and balances moisture

The operator controls heat with the wrap angle — how much of the drum’s surface the paper contacts. More wrap = more heat. This is a key lever for preventing warp, which you’ll study next lesson.

The medium often also passes a steam shower to soften it so it forms flutes without cracking.


3. The Single Facer

The single facer is the heart of the corrugator.

  1. The medium passes between two hot, fluted corrugating rolls that mesh like gears, forming it into flutes.
  2. A glue roll applies a thin line of starch to the flute tips on one side.
  3. A pressure roll (or pressure belt) presses the liner against the glued flute tips while they’re still held in the corrugating roll.
  4. Heat gels the starch, creating the single-face web — one liner + one fluted medium.

Corrugating rolls are made in a specific flute profile. Changing from C to B flute means changing the roll set — many corrugators have two single facers (for example, one B and one C) so they can make double-wall board or switch flutes quickly.

4. The Bridge

The single-face web climbs up to the bridge, an overhead conveyor where it lies in loose, overlapping folds. The bridge acts as a buffer, decoupling the single facer’s speed from the dry end, and lets the starch bond set a bit before the web moves on.


Starch: The Glue

Corrugating adhesive is a starch made from corn, wheat, or tapioca — cheap, renewable, and safe. The classic recipe (the Stein-Hall system) has two parts:

  • A carrier — a small amount of cooked starch that makes the mix thick enough to stay on the glue roll
  • Raw (uncooked) starch suspended in the carrier
  • Caustic soda to lower the gel temperature
  • Borax to boost tack and viscosity

When the glue line hits a hot flute tip, the raw starch reaches its gel point (typically around 140–150 °F / 60–65 °C), swells, and turns into a strong, clear bond almost instantly.

⚠️ Common Pitfall: Fixing Bond Problems With More Glue

Common mistake: when bonding is weak, opening up the glue gap to apply more starch.

Excess starch adds water to the board, which needs more heat to cure and causes warp and washboarding (the liner sinking between flutes). Weak bonds are often a heat or speed problem — the starch never reached its gel point — or a starch quality problem like wrong viscosity or gel temperature. Check those first. Good corrugators run the minimum glue that makes a full-fiber-tear bond.


Key Takeaway

The wet end unwinds and splices paper, preheats it to control temperature and moisture, and the single facer forms flutes and glues the first liner on. The bridge buffers the web. Starch adhesive bonds when heat brings it to its gel point — and too much starch causes more problems than it solves.

🧪 Try It: Check the Bond

Take a piece of corrugated board and peel the liner off the flutes slowly. A good bond tears fibers from the liner and medium — you’ll see fuzzy brown paper stuck to the flute tips. A poor bond peels cleanly, leaving shiny starch lines. This fiber-tear check is exactly what corrugator operators do on the floor.

🧠 Knowledge Check

1. What does the single facer produce?

2. Why do corrugators use automatic splicers?

3. How does an operator adjust preheater heat?

4. What makes the starch bond form at the flute tips?

5. A good bond, when the liner is peeled off, shows…