Converting: Flexo Folder-Gluers and Die Cutters
See how flat sheets become boxes on flexo folder-gluers, rotary die cutters, and flatbed die cutters — and how to choose between them while protecting board strength.
What “Converting” Means
The corrugator makes flat sheets. Converting turns sheets into finished boxes: printing, slotting, scoring panels, die-cutting, folding, gluing, and bundling.
Box plants come in two types:
- Corrugator plants: run a corrugator to make their own board, then convert it.
- Sheet plants: buy sheets from corrugator plants and focus on converting — often shorter runs and specialty work.
The Flexo Folder-Gluer (FFG)
For RSCs and other slotted boxes, the workhorse is the flexo folder-gluer. A sheet goes in one end and a glued, folded, counted box comes out the other — at speeds of hundreds of boxes per minute.
- 1 Feeder
Lead-edge feeder pushes one sheet at a time
- 2 Print units
One flexo unit per color
- 3 Slotter-scorer
Cuts flap slots and creases panel scores
- 4 Die-cut (optional)
Rotary section for handholes, vents
- 5 Folder-gluer
Glues the joint tab and folds the box flat
- 6 Counter-ejector
Counts and stacks bundles
- 7 Bundling
Strapping and palletizing
Notice the division of labor:
- The corrugator made the flap scores (parallel to the length of the sheet).
- The FFG makes the panel scores and cuts the slots between flaps.
Crush: The Hidden Cost of Converting
Every time the sheet passes through feed rolls, print cylinders, and pull rolls, it can be squeezed. Too much gap closure crushes the flutes and lowers caliper — and lost caliper means lost box compression strength.
Modern FFGs use vacuum transfer (holding the sheet against a belt or anvil by suction) instead of pinch rolls to reduce crush. Operators set gaps to the actual board caliper for every order.
Common mistake: tightening feed and pull roll gaps to stop print or slot registration from wandering.
It often works — but it crushes the board. Research and plant experience show converting crush can cost a meaningful share of a box’s compression strength. Fix registration with proper vacuum, clean and correctly set feed equipment, and flat board (no warp) instead of squeezing harder.
Die Cutters
For boxes that aren’t simple rectangles — mailers, trays, displays, handholes, interlocking features — the shape is cut by a die: steel cutting and creasing rules set into a base.
| Rotary die cutter (RDC) | Flatbed die cutter | |
|---|---|---|
| How it cuts | Curved die on a rotating cylinder against a soft anvil | Flat die pressed down onto the sheet |
| Speed | Fast | Slower |
| Precision | Good; can stretch slightly | Very precise; intricate shapes |
| Tooling cost | Lower-to-moderate | Higher |
| Printing | Often has inline flexo units | Usually prints elsewhere (or uses litho-laminated sheets) |
| Best for | High-volume trays, mailers, simple die-cuts | Complex displays, tight tolerances, high-graphics retail |
After die cutting, a stripping step removes the waste pieces, and the pieces may go to a specialty folder-gluer for more complex glued styles (crash-lock bottoms, for example).
Other Converting Steps
- Partition assemblers make the slotted dividers inside wine and bottle shippers.
- Stitchers close heavy boxes with metal staples.
- Laminators combine sheets or glue litho-printed paper to board (next lesson).
- Bundling and palletizing: finished boxes are strapped in bundles and loaded onto pallets for delivery — usually flat (“knocked down”) so they ship efficiently.
Key Takeaway
Converting turns sheets into boxes. The flexo folder-gluer prints, slots, scores panels, glues, and counts RSCs at high speed. Rotary die cutters are fast; flatbed die cutters are precise. Protect board caliper throughout — crushed flutes mean weaker boxes.
Take a shipping box apart at its manufacturer’s joint and flatten it. Look for: the slots between flaps (made on the FFG), the scores between panels (FFG) and between panels and flaps (corrugator), and the glue lines on the joint. Run a fingertip across the board near the score lines — any flattened bands are signs of crush from feed rolls.
1. Which machine typically prints, slots, and glues RSCs in one pass?
The flexo folder-gluer handles printing, slotting, panel scoring, folding, gluing, and counting.
2. Why does converting crush matter?
Crushed flutes reduce caliper, and caliper is a key factor in box compression strength.
3. Compared with a rotary die cutter, a flatbed die cutter is…
Flatbeds trade speed for precision and are favored for complex, tight-tolerance work.
4. How do modern FFGs reduce crush?
Vacuum transfer holds and moves the sheet without squeezing it.