Box Compression Strength and the McKee Formula
Estimate a box's compression strength with the McKee formula, then derate it for humidity, time, stacking pattern, and pallet overhang to find a safe stacking load.
What BCT Means
Box Compression Test (BCT) strength is the top-to-bottom load an empty box can carry before it buckles, measured in a compression tester under standard conditions (23 °C, 50% RH).
BCT is the number that matters on a pallet: the bottom box in a stack carries the weight of everything above it — sometimes for weeks.
Where does a box’s strength come from? Mostly the corners and the panels near them. The center of each panel bulges and carries little load. That’s why a box’s perimeter and the board’s stiffness matter so much.
The McKee Formula
In 1963, McKee, Gander, and Wachuta published a simplified formula that’s still used across the industry to estimate BCT for RSCs:
BCT ≈ 5.87 × ECT × √(caliper × perimeter)
| Term | Meaning | Units (U.S.) |
|---|---|---|
| BCT | Box compression strength | lbf |
| ECT | Edge crush test value of the board | lb/in |
| caliper | Board thickness | in |
| perimeter | 2 × (L + W) of the box | in |
The constant 5.87 is for these U.S. units. The formula works best for RSCs of ordinary proportions.
Worked Example
A 12 × 10 × 8 in RSC made of 32 ECT C-flute board, caliper 0.16 in:
- Perimeter = 2 × (12 + 10) = 44 in
- caliper × perimeter = 0.16 × 44 = 7.04
- √7.04 ≈ 2.65
- BCT ≈ 5.87 × 32 × 2.65 ≈ 498 lbf
So in the lab, this box should hold roughly 500 pounds before it collapses.
What the Formula Tells You
- ECT is linear: doubling ECT doubles BCT. Board grade is your biggest lever.
- Caliper matters (square root): crushed board loses BCT. Converting crush and flat crush both hurt.
- Perimeter matters (square root): bigger boxes are stronger — but carry heavier loads above them, too.
- Depth isn’t in the formula for typical proportions — though very tall boxes do weaken.
The Real World Is Not a Lab
That 498 lbf is under ideal conditions: a fresh box, 50% RH, a short test. In a real warehouse, the same box can lose more than half its strength. Packaging engineers apply environmental factors (multipliers) to find a safe working load.
Typical rule-of-thumb multipliers (actual values vary by source and design):
| Condition | Approximate multiplier |
|---|---|
| Storage time: 10 days / 30 days / 90 days | ~0.63 / ~0.60 / ~0.55 |
| Humidity: 50% / 70% / 80% / 90% RH | 1.00 / ~0.80 / ~0.68 / ~0.50 |
| Column-stacked (corners aligned) | ~1.00 |
| Misaligned column stacking | ~0.70–0.90 |
| Interlocked (brick) stacking | ~0.50–0.60 |
| Pallet overhang | ~0.70–0.80 |
| Pallet deck gaps under the boxes | ~0.75–0.90 |
- 1 Estimate BCT
McKee or lab test
- 2 Apply factors
Multiply by time, humidity, stacking, pallet
- 3 Required load
Weight of boxes stacked above the bottom box
- 4 Compare
Derated BCT ÷ required load = safety margin
Example, Continued
Our 498 lbf box sits 30 days in a 70% RH warehouse, interlocked on the pallet, with some overhang:
498 × 0.60 (time) × 0.80 (humidity) × 0.55 (interlock) × 0.75 (overhang) ≈ 99 lbf
The box lost about 80% of its lab strength. If each box weighs 25 lb and the stack is 5 high, the bottom box carries 4 × 25 = 100 lb — right at its limit. It will likely fail.
The fixes, in order of cost:
- Column-stack instead of interlock, and eliminate overhang — free.
- Control warehouse humidity or stack lower.
- Use a higher ECT board, or redesign so the product shares the load.
Common mistake: choosing 44 ECT “to be safe” without asking how the boxes will be stacked and stored.
An interlocked pattern with overhang can cost half the box’s strength — more than any upgrade in board grade can buy back economically. Fixing the pallet pattern is usually the cheapest strength upgrade in packaging. Ask for the pallet configuration before choosing the board.
Key Takeaway
BCT is a box’s top-to-bottom crush strength. The McKee formula estimates it from ECT, caliper, and perimeter. Real-world factors — time, humidity, stacking pattern, pallet overhang — can remove most of that strength, so engineers derate BCT and compare it to the actual load with a safety margin.
Calculate McKee BCT for a 16 × 12 × 10 in RSC made from 44 ECT C-flute board, caliper 0.17 in.
Perimeter = 2 × (16 + 12) = 56 in. caliper × perimeter = 9.52. √9.52 ≈ 3.09. BCT ≈ 5.87 × 44 × 3.09 ≈ 797 lbf.
Now derate it for 90 days at 80% RH, column-stacked, no overhang: 797 × 0.55 × 0.68 ≈ 298 lbf. How many 30-lb boxes can safely sit on top of it?
1. Which three board and box properties appear in the McKee formula?
BCT ≈ 5.87 × ECT × √(caliper × perimeter).
2. If ECT doubles and everything else stays the same, BCT…
BCT is directly proportional to ECT.
3. What is the perimeter of a 14 × 10 × 6 RSC?
Perimeter = 2 × (L + W) = 2 × (14 + 10) = 48 in. Depth isn't used.
4. Which stacking pattern typically preserves the most box strength?
Aligned columns put load on the strong corners. Interlocking can cut strength roughly in half.
5. Why does a box lose strength in high humidity?
Moisture weakens the hydrogen bonds and stiffness of paper, so compression strength drops.