Couplings & Coupling Identification
Module 4 · Couplings & Coupling Identification

Couplings & Coupling Identification

Understand the two types of hydraulic couplings, learn to read the Gates part numbering system, and identify North American, British, Japanese, German, and French thread standards.

What Are Couplings?

Couplings are the metal components of a hydraulic hose assembly. The stem end (threaded end) connects the assembly to other components in the hydraulic system.

There are two types of hydraulic couplings:

  1. Permanent — require crimping or swaging equipment
  2. Reusable (Field-Attachable) — can be installed with a vise and wrenches

⚠️ Always use NEW components. No permanent coupling part — hose, stem, or ferrule — is reusable.


Permanent Couplings

MegaCrimp® One-Piece Couplings

The ferrule is permanently attached to the stem. Designed for easy insertion — no lubrication required.

Power Crimp® Two-Piece Couplings

  • Stem — inserted into the hose
  • Ferrule — the outside shell that fits over the hose end
  • NOTE: Stem and ferrule must be compatible.

Ferrule Types

TypeDescriptionTrend
Skive ferrulesRounded serrations (teeth)Becoming obsolete; requires extra time
Non-skive ferrulesSharp serrations bite through the coverMost popular in replacement market

Field-Attachable (Reusable) Couplings

Used where crimping equipment is unavailable. Can be installed with a vise and crescent wrenches. Types include:

  • Skive
  • No-skive
  • Lock-on
  • 100R5 (C5) DOT approved

The coupling and the hose it fits on must be compatible.


Coupling Identification

HoseStemFerruleHexThread endcrimped down onto the hoseTwo-piece (PowerCrimp®)separate stem + ferruleOne-piece (MegaCrimp®)ferrule fixed to stemStraight45°90°Tee

To identify a coupling, work through four measurements in order:

  1. 1 Thread diameter

    Male OD or female ID with a caliper

  2. 2 Thread count

    Threads per inch (USA) or pitch in mm (metric)

  3. 3 Seat angle

    e.g. 37° JIC vs 45° SAE vs 24° DIN

  4. 4 Compare

    Match all three to the Gates Hydraulics Catalog


Gates Coupling Part Numbering System

Every Gates coupling follows a standardized part number that tells you exactly what you have.

Example: 12 GS - 12 FJX 90L

12GS-12FJX90LL = drop length (long)90 = degree of bendX = swivelJ = JIC (37° flare)F = female12 = stem sizeGS = stem type (GlobalSpiral™)12 = hose dash size (¾”)
CodeMeaning
12 (first)Hose Dash Size (3/4”)
GSStem Type — GlobalSpiral™
12 (second)Stem Size
FFemale
JJIC (37° Flare)
XSwivel
9090° Degree of Bend
LDrop Length (Long)

Gates Stem Style Codes

  • G20 = GlobalSpiral™
  • G25 = MegaCrimp®
  • G40 = C14 (PTFE)
  • G45 = PolarSeal®
  • G9 = Quick Disconnects

Global Part Number — Example: G25100-0808

  • G25 = MegaCrimp® series
  • 100 = Thread configuration (Male Pipe)
  • 08 = Stem size (-8 = ½”)
  • 08 = Thread size (-8 = ½”)

Coupling & Adapter End Style Codes (Reference)

CodeDescriptionCodeDescription
ABAir BrakeJJIC (37° Flare)
BO Ring BossLHLong Hex
BJBanjoMMale
BSPPBritish Pipe ParallelMMMetric Male
FFemalePPipe Thread (NPTF/NPSM)
FFFlat FaceRReusable
FLO Ring Flange (Code 61)SSAE (45° Flare)
FLHO Ring Flange (Code 62)XSwivel
FTFemale Tube4545° Bend
IInverted Flare9090° Bend
JISJapanese Industrial Standard110110° Bend

Thread Measurement

Male thread → read ODOD (outside jaws)Female thread → read IDID (inside jaws)Count threads → pitch gauge14 TPIkeep the gauge parallelto the thread axisthreads per inch / mm pitch

Key rule: When measuring threads with a pitch gauge, keep the center lines parallel — not at an angle — to get an accurate reading.


North American Thread Standards

There are 9 North American standard thread types:

Thread TypeKey FeatureNotes
National Pipe Thread (NPTF/NPSF/NPSM)Tapered threads; seal on threadsNPTF male mates with NPTF, NPSF, and NPSM female
JIC 37° Flare (MJ/FJX)Straight threads, 37° flare seatMost popular; seal made on flared seat
SAE 45° Flare (MS/FSX)Straight threads, 45° flare seatGates marks hex with a single notch to distinguish from JIC
O-Ring Boss (MB/FB/MBX)Straight threads; O-Ring seals on port faceVery reliable; resists vibration
Flat Face O-Ring (FFOR/MFFORX)O-ring in groove on flat male faceSeal when O-ring contacts flat female face
SAE Inverted 45° Flare (MIX)Straight threads; 45° inverted flareMale mates only with inverted flare female
SAE Code 61 Flange (FL)4-bolt split flangeHigh-pressure; used on pumps and motors worldwide
SAE Code 62 Flange (FLH)Thicker, higher pressure than Code 61Extremely high-pressure lines
Flareless Tube / MFACompression sleeve + 24° seatConnects hose to metal tubing

37° vs 45° Tip: The JIC 37° male/female have no markings on the hex. The SAE 45° male/female have one notch on each hex. Measure the seat angle to confirm.

24° Cone — Also used on many high-pressure applications: metric standpipe, metric bite sleeve, and German DIN / French GAZ fittings all use the 24° compression termination.


British Thread Standards

British couplings are widely used in the UK, Europe, Japan, and Commonwealth countries (India, Australia, New Zealand) and are becoming increasingly common in North America.

TypeGates CodeKey Feature
BSPPMBSPPStraight threads, 30° seat; seal with O-ring or soft metal washer
BSPTMBSPTTapered threads; seal on threads; identical to Japanese tapered pipe thread

BSPP and NPSM look similar but are NOT interchangeable — different thread pitch and 55° vs 60° angle.


Japanese Thread Standards

TypeGates CodeKey Feature
JIS 30° FlareMJIS/FJISXStraight threads, 30° seat — looks like BSPP but seat is funnel-shaped (not inverted)
Japanese Tapered PipeMBSPT/FBSPTIdentical and fully interchangeable with British BSPT
Komatsu 30° FlareMK/FKXMetric fine threads, 30° seat; 2 notches on hex to distinguish from JIS
Komatsu FlangeFLKInterchangeable with SAE Code 61; use SAE O-ring when replacing

🔑 Japanese 30° flare and BSPP threads are the same, but their seats are different — not interchangeable.


German DIN Standards

German DIN couplings are used primarily in Germany and parts of Europe.

TypeKey Feature
DIN 24°Most common; 24° seat; mates with female 24° O-Ring or female universal 24°/60° cone
DIN 60°Less common; 60° cone seat; mates with female universal 24°/60° cone
DIN 3852 Type AStraight threads; O-Ring seal on face of port
DIN 3852 Type BStraight threads; face seal
DIN 3852 Type CTapered threads; seal on threads; three series: extra light (LL), light (L), heavy (S)

DIN Light vs Heavy: Measure the tube ID — heavy series has thicker walls so the ID is smaller.


French (GAZ) Standards

TypeKey Feature
GAZ 24° Flare24° seat, metric fine threads; mates with 24° female cone or female tube coupling
GAZ Poclain 24° FlangeHigh-pressure specialty fitting; used on Poclain equipment; seal on 24° seat

Additional Coupling Selection Criteria

When selecting a coupling for any application, also consider:

FactorKey Rule
Corrosion resistanceGates uses TuffCoat™ — 400+ hours rust protection (500% better than standard 72-hr salt spray)
VibrationUse O-Ring or split-flange couplings — avoid thread-seal couplings
TemperatureUse O-Ring couplings; never use brass or aluminum in high-temp applications
Fluid compatibilityCheck chemical resistance charts for both coupling material AND O-Rings
PressureDon’t use swivel staked nut couplings at extremely high pressures; no aluminum ferrules on high-impulse
Galvanic actionAvoid mixing dissimilar metals — chemical reaction creates electrical current that weakens connections

🧠 Knowledge Check

1. What is the key difference between MegaCrimp® and Power Crimp® permanent couplings?

2. In the coupling code '12 GS - 12 FJX 90L', what does 'GS' represent?

3. How do you visually distinguish a SAE 45° flare coupling from a JIC 37° flare coupling?

4. A Japanese tapered pipe thread coupling and a British BSPT coupling look identical. Can they be interchanged?

5. Which coupling type performs best under extreme vibration?

6. What does Gates TuffCoat™ provide, and why does it matter?