Mechanical Pulping, Recycled Fiber, and Bleaching
Compare high-yield mechanical pulp with chemical pulp, follow OCC through a recycled-fiber line, and learn how modern ECF bleaching makes white pulp.
Mechanical Pulping: Tear Instead of Dissolve
Mechanical pulping separates fibers by brute force instead of chemistry. Because the lignin stays in, yield is about 90–95% — nearly double kraft.
- Stone groundwood (SGW): logs pressed against a rotating grindstone. The original method, now rare.
- Thermomechanical pulp (TMP): chips are steamed to soften the lignin, then shredded between rotating discs in a refiner. The dominant mechanical process today.
- Chemi-thermomechanical pulp (CTMP): a light chemical pretreatment before refining for stronger, cleaner fiber.
The trade-off:
| Mechanical pulp (TMP) | Chemical pulp (kraft) | |
|---|---|---|
| Yield | ~90–95% | ~45–55% |
| Strength | Low — fibers are damaged and stiff | High |
| Opacity & bulk | High | Lower |
| Brightness stability | Poor — lignin yellows in sunlight | Good once bleached |
| Energy | Very high electricity use in refiners | Largely self-supplied via recovery boiler |
| Typical use | Newsprint, magazine papers, paperboard middle plies | Linerboard, sack, fine papers, tissue |
That’s why an old newspaper left in the sun turns yellow: the lignin was never removed.
The Recycled Fiber Line
A recycled fiber (RCF) mill replaces the woodyard and digester with a line designed to turn bales of OCC into clean pulp.
- 1 Pulper
Bales slushed in water by a rotor; a ragger rope pulls out wire and plastic
- 2 Junk trap
Heavy debris — staples, rocks, glass — drops out
- 3 HD cleaning
Centrifugal cleaners spin out sand and grit
- 4 Coarse screens
Holes reject large plastics and flakes
- 5 Fine screens
Narrow slots reject stickies and shives
- 6 Thickening
Clean fiber concentrated for storage
Printing-grade recycling (old newspapers, office paper) adds a deinking step, usually flotation: air bubbles are blown through the stock, ink particles attach to the bubbles, and the froth is skimmed off.
Stickies
Stickies are tacky contaminants — pressure-sensitive label adhesive, hot-melt glue, wax, and coatings. They pass through screens when soft, then deposit on wires, felts, and dryer cans. The result is holes, sheet breaks, and downtime for cleaning. Controlling stickies is one of the biggest challenges in any recycled mill.
Bleaching
Unbleached kraft pulp is brown. For white grades, the remaining lignin must be removed or brightened in a bleach plant — a series of towers and washers, each running a different chemical stage.
Modern mills use ECF (elemental chlorine free) bleaching, built around chlorine dioxide (ClO₂). A typical sequence looks like this:
- O Oxygen delig.
Removes ~40–50% of remaining lignin before bleaching
- D₀ Chlorine dioxide
Main delignifying stage
- E Alkaline extraction
Washes out dissolved lignin; often boosted with O₂ or H₂O₂
- D₁ Chlorine dioxide
Brightening stage
- D₂ Final ClO₂ / P
Final brightness, ~88–90% ISO
- ECF eliminated elemental chlorine gas (Cl₂), dramatically cutting dioxin formation.
- TCF (totally chlorine free) uses only oxygen, ozone, and peroxide. It’s used by some mills, especially in Europe, but is more expensive and harder to reach high brightness.
- Mechanical pulp is bleached differently — with hydrogen peroxide or hydrosulfite — which brightens the lignin without removing it (so yield is preserved, but the brightness can revert).
Common mistake: overdosing chlorine dioxide to fix low brightness at the end of the line.
Brightness problems usually start upstream — a high or variable kappa number from the digester, or poor brown-stock washing that carries black liquor into the bleach plant (“carryover”). Throwing chemical at the final stage costs money and can damage fiber strength. Check washing and incoming kappa first.
Key Takeaway
Mechanical pulp keeps the lignin: high yield and opacity, low strength, yellows with age. Recycled fiber lines clean OCC with pulpers, cleaners, and screens, fighting stickies all the way. Bleaching removes or brightens lignin; modern kraft mills use ECF sequences built on chlorine dioxide and oxygen.
Cut a strip of newspaper (or the brown inner ply of a cereal box) and a strip of white copy paper. Cover half of each with a coin and leave them in direct sunlight for two or three days. Compare the covered and uncovered halves. The mechanical-pulp newsprint yellows visibly; the bleached kraft copy paper barely changes.
1. Why does mechanical pulp have a much higher yield than kraft pulp?
Mechanical pulping tears fibers apart without dissolving lignin, so about 90–95% of the wood ends up as pulp.
2. What is the job of the ragger in an OCC pulper?
Wire, tape, and plastic wrap around a rope that is slowly pulled from the pulper — the ragger.
3. What are 'stickies'?
Stickies come from adhesives and coatings in recovered paper. They deposit on machine fabrics and cause holes and breaks.
4. What chemical is the backbone of ECF bleaching?
ECF (elemental chlorine free) bleaching replaced chlorine gas with chlorine dioxide, greatly reducing dioxin formation.