Troubleshooting Sheet Breaks and Defects
Use a structured approach to find the root cause of sheet breaks, holes, wrinkles, curl, and profile problems — and learn the defect patterns every operator should recognize.
Why Breaks Are So Expensive
When the sheet breaks, the machine keeps running but makes nothing saleable. Everything goes to the couch pit or broke pulper until the crew threads a narrow tail back through the machine and widens it to full width.
On a large machine, every minute of break time can mean a ton or more of lost production. A mill tracking break frequency and minutes lost per break is tracking money.
A Structured Approach
Good troubleshooters don’t guess. They work the problem the same way every time.
- 1 Locate
Where did the break start? Break-detection cameras, broke location
- 2 Characterize
Edge or center? Clean tear or hole? Pattern repeating?
- 3 Correlate
What changed? Grade, furnish, chemistry, felt, speed, shift
- 4 Hypothesize
One likely cause, with evidence
- 5 Test & verify
Change one thing; confirm with data
- 6 Standardize
Update procedures so it stays fixed
Web inspection and break-detection camera systems record video around the machine. Rewinding the footage to the moment of the break is often the fastest way to see where it started.
Repeating Defects: Do the Math
If a defect repeats at a regular interval in the MD, measure the spacing. Then compare it with the circumference of rolls and fabrics:
Repeat distance = π × roll diameter (for a roll) or the fabric length (for a felt or wire)
A spot every 1.88 m? That matches a roll about 0.6 m in diameter. Find which rolls in the machine are that size, and inspect them for a damaged cover, a deposit, or a doctor blade problem.
Common Defects and Likely Causes
| Defect | What it looks like | Common causes |
|---|---|---|
| Holes | Round or ragged openings | Stickies, slime, pitch deposits falling from machine surfaces; foam; shives |
| Spots / dirt | Specks in the sheet | Bark, dirt, plastics passing cleaners; scale deposits |
| Edge cracks | Breaks starting at the edge | Wet or weak edges, edge trim problems, draw problems |
| Wrinkles | Creases in MD | Uneven moisture or caliper profile, misaligned rolls, slack sheet |
| Wet streaks | MD bands with high moisture | Plugged felt, steam shower problems, headbox slice issues |
| Curl | Sheet won’t lie flat | Moisture or fiber-orientation differences between top and bottom |
| Blisters | Bubbles in the sheet | Too-rapid drying of a wet sheet; trapped steam |
| Slime holes | Gelatinous lumps then holes | Microbiological growth in the white-water system |
Deposits and Housekeeping
Many breaks trace back to deposits — pitch from wood, stickies from recycled fiber, scale from hard water, and biological slime. They build up on surfaces, then break loose and land on the sheet. Controls include:
- Biocide programs in the white water loop
- Deposit control chemicals and fixatives
- Showers and doctor blades that keep rolls and fabrics clean
- Scheduled boil-outs and washups during shutdowns
Common mistake: after a bad shift of breaks, the team changes the felt shower, adds retention aid, and slows the machine — all at the same time.
Breaks drop. Great — but nobody knows which change worked, so nobody knows which one to keep, and the same problem comes back next month. Unless safety or a customer order demands it, change one variable at a time and let the data settle before the next change.
Key Takeaway
Breaks and defects are expensive; a structured approach — locate, characterize, correlate, hypothesize, test, standardize — finds root causes faster than guessing. Repeating defects can be traced to specific rolls by matching the repeat distance to roll circumference. Many holes and breaks start as deposits, so cleanliness is a production strategy.
A customer reports a small dent in their linerboard every 1.41 m along the roll. The mill has dryer cans at 1.83 m diameter, a calender roll at 0.45 m, and a felt-carrying roll at 0.60 m.
Compute each circumference (π × D): dryer cans ≈ 5.75 m; calender roll ≈ 1.41 m; felt roll ≈ 1.88 m. The calender roll matches — check it for a dent or deposit.
1. What is a 'tail' on a paper machine?
After a break, crews thread a narrow tail through the machine, then spread it to full width.
2. A defect repeats every 1.88 m in the machine direction. What should you suspect?
π × 0.6 m ≈ 1.88 m. A regular repeat points to a roll or fabric with that circumference.
3. What commonly causes slime holes?
Bacteria and fungi form slime deposits that break loose and cause holes. Biocide programs control them.
4. Why should you change one variable at a time when troubleshooting?
Changing several things at once hides the true cause, so the fix can't be standardized.