Forming the Sheet and Wet-End Chemistry
Follow the jet onto the wire, learn how Fourdrinier and twin-wire formers drain water, why fiber orientation creates MD and CD, and how retention aids, sizing, and strength additives work.
The Forming Section
The headbox jet lands on the forming fabric (still called the wire, even though modern fabrics are woven plastic). In a few meters and a fraction of a second, the stock goes from ~99% water to a self-supporting wet web at roughly 20% solids.
Water is removed by elements under the fabric, in this order:
| Element | How it drains |
|---|---|
| Forming board | Supports the fabric where the jet lands; gentle initial drainage |
| Foils | Angled blades that create a mild vacuum as the fabric passes; also agitate stock to break up flocs |
| Vacuum boxes | Suction boxes that pull harder once a mat has formed |
| Couch roll | A perforated suction roll at the end; the web is transferred off the wire here |
You’ll often see a dry line partway down the table — the point where the glossy water layer on top disappears and the sheet turns matte. Operators watch it: if the dry line moves, drainage has changed.
Fourdrinier vs. Twin-Wire Formers
- Fourdrinier: a single flat wire; water drains downward only. Simple and still common for containerboard.
- Gap and hybrid formers: the jet is caught between two fabrics, draining water from both sides. This gives better formation (evenness), less two-sidedness (different top and bottom surfaces), and much higher speed. Most new printing-paper and tissue machines use twin-wire forming.
- Multi-ply forming: board machines often form two or three plies separately — for example, a cheaper recycled middle ply between clean outer plies — and combine them while wet.
Machine Direction and Cross Direction
Because the jet is moving at nearly the same speed as the wire, most fibers line up pointing downstream. That gives every sheet of paper a “grain.”
- MD (machine direction): the direction the paper travels. Higher tensile strength and stiffness.
- CD (cross direction): across the width. More expansion and shrinkage with moisture.
The jet-to-wire speed ratio controls how strongly fibers align. In corrugated board, the corrugator runs the paper so the flutes go across it — you’ll see why that matters in the box course.
Wet-End Chemistry
The wet end is where chemistry happens. Small doses of additives make a huge difference.
Retention Aids
Fines, fillers, and additives are tiny — many would drain straight through the wire. Retention aids (usually cationic polymers, sometimes paired with microparticles like bentonite or colloidal silica) flocculate those small particles onto fibers so they stay in the sheet. Better retention means a cleaner white-water loop and less waste.
Sizing
Untreated paper wicks water like a paper towel. Internal sizing makes it water-resistant:
- AKD (alkyl ketene dimer) and ASA (alkenyl succinic anhydride) react with the cellulose in neutral/alkaline papermaking — the modern standard.
- Rosin size with alum is the traditional acidic system, still used in some containerboard.
Surface sizing — starch applied at the size press — is covered in the next module.
Strength Additives
- Cationic starch (dry strength) — the most common additive in containerboard.
- Wet-strength resins (such as PAE) — for towel, liquid packaging, and labels that must survive getting wet.
Fillers
Printing papers add mineral fillers — precipitated calcium carbonate (PCC), ground calcium carbonate (GCC), clay, or titanium dioxide — for opacity, brightness, and smoothness. Fillers are cheaper than fiber but weaken bonding, so there’s always a trade-off.
Common mistake: adding more and more cationic polymer when retention drops.
Cellulose fibers and many contaminants are anionic (negatively charged). Recycled furnish brings in a lot of dissolved and colloidal “anionic trash” that soaks up cationic additives before they reach the fiber. Mills measure the charge demand of the white water (and the zeta potential of the fibers). When charge balance drifts, the fix might be a cheap fixative to neutralize the trash first — not more expensive retention aid.
Key Takeaway
The forming section drains stock from ~99% to ~80% water with foils, vacuum, and the couch. Twin-wire formers drain from both sides for better formation and speed. Fiber alignment creates MD and CD properties every converter cares about. Wet-end chemistry — retention aids, sizing, starch, and fillers — tunes the sheet, and depends on keeping the system’s charge in balance.
Take a sheet of copy paper. Tear it slowly lengthwise, then across. One tear runs straight and clean — that’s with the grain (MD). The other wanders. Next, wet one edge of a strip cut each way and watch which one curls more. You’ve just found MD and CD without a lab.
1. What does the 'dry line' on a Fourdrinier table indicate?
The dry line is where the glossy water layer vanishes. A shifting dry line signals a change in drainage.
2. Why do twin-wire formers produce less two-sidedness than a Fourdrinier?
Draining from both sides keeps fines and fillers more evenly distributed between top and bottom surfaces.
3. In which direction is paper typically stronger in tension?
Most fibers align with the direction of travel, so MD tensile strength is higher.
4. What do AKD and ASA do?
AKD and ASA are reactive internal sizing agents used in neutral/alkaline papermaking.
5. Why can recycled furnish make cationic retention aids less effective?
Dissolved and colloidal anionic material uses up cationic additives. Measuring charge demand helps diagnose this.