Stock Prep, Refining, and the Approach Flow
Learn how refining develops fiber for bonding, why freeness is the number everyone watches, and how stock is blended, cleaned, and delivered to the headbox.
Meet the Paper Machine
Before diving into stock prep, here’s the whole machine in one picture. Notice how the solids content climbs from left to right — every section’s job is to remove water.
This module covers the left end: preparing the stock (the fiber–water slurry) and getting it onto the wire.
Refining: Developing the Fiber
Pulp straight from the digester or pulper doesn’t bond well. Refining fixes that. Stock is pumped between two discs (or a cone and shell) covered in metal bars, rotating against each other at a very small gap.
Refining does three things to fibers:
- Internal fibrillation — loosens the fiber wall so the fiber becomes flexible and collapses flat.
- External fibrillation — raises tiny fibrils on the surface, like fraying a rope, giving far more bonding area.
- Cutting — shortens fibers. Usually undesirable for strength grades.
More refining means more bonding → higher tensile and burst strength, a denser, smoother sheet. But it comes at a cost.
Freeness: The Number Everyone Watches
Freeness measures how quickly water drains from a pulp sample. In North America it’s reported as Canadian Standard Freeness (CSF) in milliliters. (Europe uses Schopper-Riegler, °SR, which runs in the opposite direction.)
- High CSF = drains fast = lightly refined
- Low CSF = drains slowly = heavily refined
Refining creates a tug-of-war:
| More refining (lower CSF) | Effect |
|---|---|
| ✅ | Stronger, denser, smoother sheet |
| ❌ | Water drains slower on the wire |
| ❌ | Wetter sheet entering the dryers → more steam, or a slower machine |
| ❌ | More refiner electricity |
Common mistake: a burst test comes back low, so the refiner load gets cranked up.
Strength improves — but freeness drops, the wire can’t drain the stock, the sheet hits the dryers wetter, and the machine has to slow down. You traded a quality problem for a production problem. Before adding refining, check the fiber furnish, starch dosage, and wet-end chemistry. Refining is a lever, not a cure-all.
Blending and the Approach Flow
After refining, stocks are combined in a blend chest — softwood, hardwood, recycled fiber, and broke (the mill’s own off-spec or trimmed paper, repulped and reused). Additives are dosed here or just downstream.
The approach flow is the final stretch from the machine chest to the headbox. Its job is to deliver perfectly uniform, clean, pulse-free stock.
- 1 Machine chest
Stock at ~3% consistency, steady level
- 2 Basis weight valve
Meters the exact fiber flow
- 3 Fan pump
Dilutes with white water to <1% and pumps to headbox
- 4 Cleaners
Centrifugal cleaners remove dirt and grit
- 5 Pressure screen
Last chance to catch shives and debris
- 6 Headbox
Spreads stock evenly across the full width
White water — the water that drains through the wire — is collected in the wire pit and reused to dilute the incoming stock at the fan pump. This short circulation loop saves water and recaptures fine fibers and fillers that drained through.
The Headbox
The headbox turns a pipe of stock into a thin, perfectly even jet as wide as the machine — sometimes over 10 meters. Inside, a tube bank and turbulence generators break up fiber clumps (flocs). The jet exits through an adjustable slice lip.
Modern headboxes use dilution control: dozens of small valves across the width add white water locally to fine-tune basis weight in the cross-machine direction (CD).
Key Takeaway
Refining develops bonding at the expense of drainage, and freeness (CSF) tracks that trade-off. Stocks are blended, then the approach flow meters, dilutes, cleans, and screens the stock before the headbox delivers an even jet onto the wire.
Tear a sheet of paper towel and a sheet of copy paper into small pieces. Soak each in a separate cup of water and blend or stir hard until mushy. Pour each slurry through a kitchen strainer and watch the drainage.
The towel pulp (lightly refined, bulky) drains fast — high freeness. The copy paper pulp (more refined, more fines) drains slower — lower freeness.
1. What is the main purpose of refining?
Refining fibrillates and flexes fibers, increasing bonding area and therefore strength.
2. A lower CSF (Canadian Standard Freeness) number means the pulp…
CSF measures drainage. Low CSF = slow drainage = more heavily refined.
3. What is 'broke'?
Broke is the mill's own paper — trim, reel turn-ups, off-spec — repulped and blended back into the furnish.
4. Where is the stock diluted with white water to below 1% consistency?
The fan pump mixes thick stock with white water from the wire pit and pumps the dilute stock to the headbox.
5. What does headbox dilution control adjust?
Small dilution valves across the width fine-tune local consistency to level the CD basis weight profile.