The Energy Control Program and Who Does What
Learn the three pillars of an OSHA energy control program (written procedures, training, and periodic inspections), what a machine-specific procedure must contain, and the difference between authorized, affected, and other employees.
Three Pillars
OSHA 1910.147 requires an energy control program with three parts:
- 1 Procedures
Written, machine-specific steps
- 2 Training
By role; retrain when things change
- 3 Periodic inspection
At least annually; certified
A binder of procedures nobody follows is not a program. All three pillars have to work together.
Who Does What: The Three Roles
| Role | Who | What they must know |
|---|---|---|
| Authorized employee | The person who locks or tags out equipment to service it | Recognize hazardous energy sources, the type and magnitude of energy, and the methods to isolate and control it |
| Affected employee | Someone who operates or uses the equipment, or works in the area where servicing happens | The purpose and use of energy control procedures; never try to restart locked or tagged equipment |
| Other employee | Anyone whose work may be in an area where LOTO is used | The procedure exists, and they must not remove locks or restart equipment |
An affected employee becomes an authorized employee when they perform servicing that requires LOTO. They need that training first.
Machine-Specific Procedures
General “how to lock out” instructions aren’t enough for most equipment. OSHA requires documented procedures that clearly spell out, for the equipment involved:
- The intended use of the procedure (which machine, which tasks)
- Steps for shutting down, isolating, blocking, and securing the machine
- Steps for placing, removing, and transferring lockout/tagout devices, and who is responsible
- Requirements for testing the machine to verify the effectiveness of the lockout
What Good Procedures Look Like
Most plants use one-page visual procedures posted at the machine:
- Photos of each isolation point, numbered
- Energy type and magnitude (e.g., “480 VAC,” “90 psi air,” “2,000 psi hydraulic accumulator”)
- Device location and the method (e.g., “Turn handle OFF, apply lock”)
- Stored energy steps (bleed, block, discharge)
- Verification method for each source
- Release steps
When Documentation Isn’t Required
OSHA’s standard includes a narrow exception: a written procedure isn’t needed for a specific machine if all of a list of conditions are met. These include that the machine has no potential for stored or residual energy after shutdown, has a single energy source that can be readily identified and isolated, isolation fully de-energizes it, it’s locked by a single lockout device under the exclusive control of the authorized employee, and there have been no prior accidents involving unexpected activation during servicing. If any condition isn’t met, write the procedure. Most industrial machines don’t qualify.
Training
| When | Requirement |
|---|---|
| Initial | Before an employee performs or is affected by LOTO, appropriate to their role |
| Retraining | When job assignments change, machines or processes change and create new hazards, procedures change, or a periodic inspection (or other reason) shows deviations or gaps in knowledge |
| Documentation | The employer must certify that training was done, with names and dates |
If your plant uses tags only for some equipment, training must also cover the limitations of tags (Lesson 2.2).
Common mistake: procedures are written from drawings by someone who never walked the machine.
The result: a missed second disconnect, a valve that’s actually behind the machine, an accumulator nobody listed. Write and validate every procedure at the machine, with the people who service it, and test it by actually performing the lockout.
Key Takeaway
An energy control program has procedures, training, and periodic inspections. Authorized employees apply locks; affected employees operate the equipment and must never restart it while locked out; other employees must leave it alone. Procedures must cover shutdown, isolation, device placement and removal, stored energy, and verification, and should be visual and validated at the machine.
Classify each person during a gearbox replacement on a palletizer:
- The millwright who locks out the palletizer and removes the gearbox. (Authorized.)
- The palletizer operator who is told the machine is down. (Affected.)
- A forklift driver who passes through the area. (Other.)
- The operator who later helps lock out to adjust a sensor. (Becomes authorized. Must be trained as authorized first.)
1. What are the three main parts of an energy control program?
OSHA requires documented procedures, training, and periodic inspections.
2. Who applies lockout devices to service a machine?
Authorized employees perform lockout to service equipment.
3. Which of these must a machine-specific procedure include?
Procedures must include verification steps, along with shutdown, isolation, and device placement and removal.
4. When must retraining occur?
Retraining is triggered by changes and by evidence of gaps or deviations.