Group Lockout, Shift Changes, and Contractors
Module 4 · Complex Lockouts

Group Lockout, Shift Changes, and Contractors

Handle complex lockouts safely: group lockout with a lockbox and a primary authorized employee, continuity of protection across shift changes, and coordinating energy control with outside contractors.

When One Lock Isn’t Enough

Big jobs, such as a paper machine shutdown, a line rebuild, or a boiler outage, can involve dozens of isolation points and many workers from several crews. Every person still needs the same protection they’d get from their own personal lock.


Group Lockout

OSHA 1910.147 requires group lockout procedures to give each authorized employee a level of protection equivalent to a personal lockout device.

The Lockbox Method

  1. 1 Isolate

    Primary locks every energy point

  2. 2 Keys in box

    Isolation keys go in the lockbox

  3. 3 Verify

    Primary verifies zero energy

  4. 4 Workers lock box

    Each applies a personal lock

  5. 5 Work

    Each may check verification

  6. 6 Remove

    Each removes only their own lock

Nobody can retrieve the isolation keys until every personal lock is off the box.

The Primary Authorized Employee

One authorized employee has primary responsibility for the group. They:

  • Coordinate the lockout of all isolation points
  • Make sure each group member has applied their personal lock
  • Know the status of everyone on the job
  • Ascertain the exposure status of each member before work and before release

When multiple crews or departments are involved, one authorized employee is designated to coordinate among the crews.

Each Worker’s Right to Verify

Each worker’s personal lock on the box is their protection. Good programs also let each worker see the verification, or perform their own try-out, before going in. Never put your lock on a box for a job whose isolation you don’t trust. Ask.

⚠️ Common Pitfall: Locking the Box, Then Leaving the Plant

Common mistake: a contractor finishes their part, forgets their lock is on the group lockbox, and leaves for the day.

Now nobody can complete the job without the special lock-removal procedure (Lesson 5.1). The fix is administrative: a sign-in/sign-out board at the lockbox, and a supervisor check before anyone leaves the job.


Shift and Personnel Changes

Long jobs often span shifts. OSHA requires specific procedures to ensure continuity of lockout protection during shift or personnel changes, including the orderly transfer of devices between outgoing and incoming employees.

A safe handoff:

  1. Incoming worker applies their lock first.
  2. Outgoing worker then removes theirs.
  3. Both review the job status, energy status, and hazards.
  4. The handoff is documented (log or sign board).

At no moment should the equipment be without a lock from someone actively protected by it.


Outside Contractors

When contractors service equipment, OSHA requires:

  • The host employer and the contractor inform each other of their respective lockout/tagout procedures.
  • The host employer ensures its employees understand and comply with the contractor’s energy control program.

In practice, many sites require contractors to follow the host’s procedures, use host-issued or approved locks, and attend a site orientation. What matters is that everyone uses one agreed system and understands it before work starts.


Key Takeaway

Group lockout must protect each worker as well as a personal lock, usually with a lockbox where every worker adds their own lock. A primary authorized employee coordinates and tracks everyone. Shift changes use lock-on-before-lock-off handoffs. Host and contractor must exchange and agree on LOTO procedures before work starts.

🧪 Try It: Plan a Group Lockout

A conveyor system rebuild involves 4 mechanics, 2 electricians, and a contractor crew of 3. There are 11 isolation points across two motor control centers and three air drops.

Sketch your plan:

  1. Who is the primary authorized employee?
  2. Where will the lockbox and sign-in board be?
  3. How will each worker verify isolation?
  4. How will the contractor be briefed on your procedure?
  5. What happens at shift change if the job runs overnight?
🧠 Knowledge Check

1. In group lockout, what level of protection must each worker receive?

2. In the lockbox method, what goes into the lockbox?

3. What is the correct order for a shift-change handoff?

4. When a contractor services equipment, OSHA requires the host and contractor to: