Testing, Positioning, and Alternative Measures
Learn the OSHA sequence for temporarily removing locks to test or position a machine, how to design effective alternative measures for routine minor servicing, and how energized troubleshooting is handled under electrical safety rules.
When You Need Energy Back, Briefly
Some jobs require power partway through: jogging a conveyor to line up a splice, bumping a motor to check rotation, or running a machine to test a repair. OSHA allows lockout devices to be temporarily removed for testing or positioning, but only in a specific sequence.
- 1 Clear tools
Remove tools and materials
- 2 Clear people
Everyone out of the machine area
- 3 Remove locks
Using the release procedure
- 4 Energize
Test or position
- 5 Re-lock
De-energize; full lockout again
Key points:
- Treat the removal exactly like a full release (Lesson 5.1): inspect, notify, and account for everyone.
- When you’re done testing, the machine goes back to a fully locked and verified state before anyone goes back in.
- No one works inside the danger zone while energy is restored.
Common mistake: a mechanic stays inside to guide a belt while a coworker jogs the motor “just a bump.”
That’s servicing in the danger zone with energy restored, which is exactly what LOTO is meant to prevent. If positioning needs a hand inside, use a method that keeps hands out (hand-turning with locks on, a barring device, or a dedicated, safeguarded inching mode designed for this purpose under a documented procedure).
Alternative Measures for Minor Servicing
Recall the minor servicing exception: routine, repetitive tasks integral to production don’t require LOTO if effective alternative measures protect the worker. Examples of well-designed alternatives:
| Task | Alternative measure |
|---|---|
| Clearing a jam at a guarded infeed | Interlocked guard monitored by a safety-rated system that stops hazardous motion and prevents restart while open |
| Adding labels to a running labeler | Tool or access port that keeps hands outside the danger zone |
| Wiping a sensor lens | Sensor relocated or a cleaning port added outside the guard |
| Clearing a film wrap at a stretch wrapper | Safety-rated stop plus a trapped-key system for guard entry |
What makes them effective:
- Designed using risk assessment and machine safety standards (such as ANSI B11 and ISO 13849 for safety-rated controls)
- Protect against all hazards for that task, including stored energy
- Documented, with training, so the task is done the same way every time
If a task falls outside the defined alternative measure (a bigger jam, a different access point, a broken interlock), go back to full lockout.
Energized Electrical Troubleshooting
Diagnosing electrical faults sometimes requires taking voltage measurements on live circuits. That isn’t lockout; it’s energized work, governed by electrical safe work practices such as OSHA 1910.333 and NFPA 70E. In general:
- Only qualified persons do it.
- Work on energized parts must be justified. De-energizing is the default.
- The hazards (shock and arc flash) are assessed, and appropriate PPE, tools, and boundaries are used.
- Many sites require an energized electrical work permit for anything beyond diagnostic testing.
Once troubleshooting finds the problem, the repair is done under lockout.
Key Takeaway
You may temporarily remove locks to test or position only by following the sequence: clear tools, clear people, remove locks per release, energize, then fully re-lock before resuming. Minor servicing alternatives must be engineered, documented, and effective against all hazards. Live electrical troubleshooting is energized work under electrical safety rules, and repairs happen under lockout.
After replacing a motor, the electrician needs to check rotation direction. Write the steps they should follow.
Clear all tools from the drive. Make sure everyone is out of the machine area. Notify affected employees. Remove locks using the release procedure. Bump the motor and observe rotation from a safe position. De-energize, re-apply all locks, release stored energy, and verify before correcting the rotation (swapping leads) under lockout.
1. What must happen before locks are removed to test a machine?
OSHA's sequence starts with clearing tools and people before devices are removed.
2. After testing or positioning, what must happen before servicing resumes?
The machine must return to a fully locked and verified state.
3. Which is an example of an effective alternative measure for routine jam clearing?
Engineered, safety-rated interlocks provide effective protection. Administrative requests alone do not.
4. Live voltage measurements during troubleshooting are governed by:
Energized work requires qualified persons, justification, risk assessment, and PPE under electrical safety rules.