Periodic Inspections and Common Program Failures
Conduct the annual periodic inspection OSHA requires, certify it correctly, and learn the most common ways LOTO programs fail in practice so you can catch them before an injury does.
The Annual Check-Up
OSHA requires employers to conduct a periodic inspection of each energy control procedure at least annually to make sure the procedure and the standard’s requirements are being followed.
Who Inspects
The inspection must be done by an authorized employee other than the one(s) using the procedure being inspected. In other words, you can’t inspect your own lockout. Many plants use trained peers from another area, maintenance planners, or safety staff who are also authorized employees.
What the Inspection Includes
- 1 Select
Procedure and machine
- 2 Observe
Watch it performed for real
- 3 Review
Responsibilities with each worker
- 4 Correct
Fix deviations and gaps
- 5 Certify
Machine, date, people, inspector
- Observe the procedure being performed, not just read it. Is every step followed? Is every energy source isolated and verified?
- Review responsibilities with each authorized employee using the procedure (for lockout). Where tagout is used, the review covers each authorized and affected employee and includes the limitations of tags.
- Correct any deviations or inadequacies found.
Certification
The employer must certify that periodic inspections were performed. The certification identifies:
- The machine or equipment the procedure was used on
- The date of the inspection
- The employees included in the inspection
- The person performing the inspection
Machines that share the same procedure can be grouped, but the inspection should still reflect real-world use.
How LOTO Programs Fail
Lockout/tagout consistently appears on OSHA’s list of the most frequently cited standards. The citations and incident investigations show the same patterns again and again:
| Failure | What it looks like on the floor |
|---|---|
| No written procedures or generic ones | A one-size “Turn off, lock, tag” sheet for every machine |
| Procedures don’t match the machine | Missing energy sources, wrong disconnect numbers, no stored energy steps |
| No verification | Locks applied, nobody tries to start or tests for voltage |
| No periodic inspections, or “paper” inspections | Signed forms with nobody actually observed |
| Inadequate training | Operators don’t know what affected means; new hires untrained |
| Minor servicing misuse | Routine jam clearing done with guards open and no effective alternative |
| Shared or missing locks | One lock for a crew; personal padlocks from home |
| Unsafe lock removal | Locks cut without the absent-employee procedure |
| Contractor gaps | Contractors using their own system with no coordination |
Common mistake: the program binder is flawless, with every machine documented and every inspection signed, but nobody has watched an actual lockout in years.
Auditors and investigators look at what happens on the floor. Real periodic inspections mean watching someone lock out, asking them to explain each step, and fixing what you find.
Leading Indicators
Don’t wait for an injury to measure your program. Track:
- Percentage of machines with validated, machine-specific procedures
- Periodic inspections completed on time, and number of deviations found and closed
- Near misses reported involving energy control
- Training completion by role
- Lock removal exceptions (each one should be reviewed)
Key Takeaway
Inspect each procedure at least annually, done by an authorized employee who isn’t using it, by observing real use and reviewing responsibilities. Certify with machine, date, employees, and inspector. Watch for the classic failures: generic procedures, no verification, paper inspections, misuse of minor servicing, and unsafe lock removal.
Ask a qualified coworker to perform a lockout on a machine (with real isolation). As the observer, check:
- Did they notify affected employees?
- Did they use a normal stop first?
- Did they isolate every source listed on the procedure, and was anything missing from the procedure?
- Did they handle stored energy?
- Did they verify with a try-out and testing, then return controls to OFF?
- Could they explain their responsibilities?
Record what you found and one improvement for the procedure.
1. How often must periodic inspections of energy control procedures be conducted?
OSHA requires periodic inspections at least annually.
2. Who may perform the periodic inspection?
The inspector must be an authorized employee who isn't the one using the procedure being inspected.
3. What must the inspection certification identify?
Certification must identify the equipment, date, employees included, and person performing the inspection.
4. Which is a sign of a 'paper' LOTO program?
Inspections must involve observing and reviewing real practice, not just signing forms.