Rigging Hardware and Inspection
Module 3 · Rigging

Rigging Hardware and Inspection

Learn wire rope, alloy chain, and synthetic slings, the vertical, choker, and basket hitches, shackles and hooks, working load limits, and the ASME B30 inspection and removal criteria that keep damaged gear off the hook.

Rigging Connects the Crane to the Load

Containers lift with spreaders, but breakbulk, project cargo, hatch covers, equipment, and maintenance lifts all need rigging: slings, shackles, hooks, and spreader bars. Rigging that fails drops the load, no matter how good the crane is.

Key U.S. standards include ASME B30.9 (slings), B30.26 (rigging hardware), and B30.10 (hooks), plus OSHA rules for marine terminals and longshoring.


Working Load Limit (WLL)

Every piece of rigging has a Working Load Limit (WLL), also called rated capacity, marked on its tag or body. It’s the maximum load the manufacturer allows in normal service, with a built-in design factor (for example, around 5:1 for many wire rope and synthetic slings and alloy chain at 4:1, as set by the applicable standard and manufacturer).

Never exceed the WLL. The design factor is for wear, dynamic loading, and uncertainty, not extra capacity.

No tag, no lift. A sling with a missing or unreadable ID tag must be removed from service.


Sling Types

SlingStrengthsWatch for
Wire ropeStrong, durable, heat-tolerantBroken wires, kinks, crushing, birdcaging, corrosion
Alloy chain (Grade 80 or 100)Rugged, heat- and abrasion-resistant, adjustableStretch, cracks, nicks, gouges, bent links. Only alloy chain is used for overhead lifting, never transport or proof-coil chain.
Synthetic webLight, flexible, protects finished surfacesCuts, burns, chemical damage, worn stitching; needs edge protection
Synthetic round slingVery flexible, lightCuts; exposed core yarns; many have warning yarns that show when the cover is damaged

Wire Rope Basics

Wire rope is made of wires twisted into strands, laid around a core. A common designation like 6×19 IWRC means 6 strands of about 19 wires each, around an independent wire rope core (stronger and more crush-resistant than a fiber core).


Hitches

HitchDescriptionCapacity vs. vertical (typical)
VerticalSingle leg straight up100% of the vertical rating
ChokerSling wraps the load and passes through its own eyeLess: often around 75–80% for wire rope at standard choke angles; check the tag
BasketSling cradles the load, both eyes on the hookUp to 200% when legs are vertical; less as legs angle out

The sling’s tag lists capacities for each hitch type. Angles reduce capacity further (Lesson 3.2).


Shackles and Hooks

Shackles

  • Screw pin shackles for temporary lifts; bolt-type (safety) shackles with a nut and cotter pin for long-term or rotating loads.
  • WLL is marked on the body. Use only load-rated shackles.
  • Load the shackle in line; side loading reduces capacity per the maker’s chart.
  • Never replace a pin with a bolt.

Hooks

  • Should have a working safety latch (where required).
  • Load sits in the bowl (saddle), never on the tip.
  • Remove from service if the throat opening has increased or the hook is twisted beyond limits (ASME B30.10 and the maker give criteria), or if there are cracks.

Inspection

InspectionWhenWho
Pre-use / frequentBefore each use or each shiftCompetent person (often the rigger)
PeriodicAt set intervals (often at least annually; more often in severe service)Qualified/competent person; documented

Removal Criteria (Examples from ASME B30.9 for Slings)

Wire rope slings (single-part): remove for 10 randomly distributed broken wires in one rope lay, or 5 broken wires in one strand in one rope lay; kinking, crushing, birdcaging, or other distortion; heat damage; severe corrosion; damaged end fittings; missing or unreadable ID tag.

Synthetic slings: remove for cuts, tears, holes, burns, melting, charring, chemical damage, broken stitching in load-bearing splices, exposed warning yarns or core, knots, or a missing tag.

Alloy chain: remove for cracks, stretch beyond the maker’s limit, nicks and gouges, excessive wear, bent or twisted links, or a missing tag.

Damaged gear gets tagged out and removed from the work area so it can’t be grabbed by mistake.

⚠️ Common Pitfall: Tying a Knot in a Sling to Shorten It

Common mistake: a web sling is too long, so someone ties a knot in it.

Knots can cut sling strength drastically and damage fibers. Use the correct length sling, an adjustable chain sling, or a proper shortening device rated for the purpose.


Key Takeaway

Every piece of rigging has a WLL. No tag, no lift. Choose wire rope, alloy chain, or synthetic slings for the job, and protect synthetics from edges. Chokers reduce capacity; baskets can double it with vertical legs. Load shackles in line and hooks in the bowl. Inspect before each use and periodically, and remove damaged gear using ASME B30 criteria.

🧪 Try It: Inspect These Slings

Decide: keep or remove?

  1. Wire rope sling with 3 broken wires in one strand within one lay, tag readable. (Below the 5-in-one-strand limit, so it may stay in service if there’s no other damage. Monitor closely.)
  2. Polyester round sling with red warning yarn showing through a cut cover. (Remove.)
  3. Grade 80 chain sling with no tag. (Remove. No tag, no lift.)
  4. Web sling with a small melted spot from welding spatter. (Remove. Heat damage.)
🧠 Knowledge Check

1. A sling's ID tag is missing. What should you do?

2. Which chain may be used for overhead lifting?

3. How does a choker hitch affect sling capacity compared with a vertical hitch?

4. Under ASME B30.9, a single-part wire rope sling should be removed for: