Crane Signals and Communication
Learn the standard ASME hand signals for crane operation, the role of the qualified signal person, radio communication discipline, and the rule that anyone can call a stop.
Why Signals Matter
Crane operators often can’t see the load or the landing spot, especially when working deep in a ship’s hold, behind a stack, or on the far side of a vessel. The signal person is the operator’s eyes. Clear, standard communication prevents collisions, crushed hands, and dropped loads.
The Signal Person
- Must be qualified: knows the standard signals, crane motions, and the hazards of the operation, as required by the applicable rules and site procedures.
- There should be one designated signal person giving directions at a time, so the operator isn’t getting conflicting signals.
- Must be clearly visible to the operator (high-visibility gear or gloves) or in clear radio contact.
- Must have a clear view of the load and path, or relay through another qualified person.
Anyone Can Stop
The operator follows only the designated signal person, except for STOP. Anyone who sees danger may signal STOP or EMERGENCY STOP, and the operator must obey immediately.
Standard Hand Signals
These are based on the standard signals published in the ASME B30 crane standards. Charts are usually posted on or near the crane. Learn them exactly.
| Command | Signal |
|---|---|
| Hoist | Forearm vertical, forefinger pointing up, move hand in small horizontal circles |
| Lower | Arm extended down, forefinger pointing down, move hand in small horizontal circles |
| Stop | Arm extended, palm down, move arm back and forth horizontally |
| Emergency stop | Both arms extended, palms down, move arms back and forth horizontally |
| Dog everything (pause all motions) | Clasp hands in front of the body |
| Swing (slewing cranes) | Arm extended, point finger in the direction to swing |
| Trolley travel | Palm up, fingers closed, thumb pointing in direction of travel, jerk hand horizontally |
| Bridge / gantry travel | Arm extended forward, hand open and slightly raised, make a pushing motion in the direction of travel |
| Move slowly | Use one hand for the motion signal and place the other hand motionless in front of it (e.g., above the hoist signal hand) |
| Raise boom | Arm extended, fingers closed, thumb pointing up |
| Lower boom | Arm extended, fingers closed, thumb pointing down |
Port terminals may have additional site-specific signals for spreader operations and ship work. Use the site’s posted chart.
Radio Communication
On ships and in terminals, many lifts use radios because of distance and noise.
- Use a dedicated channel for the lift when possible.
- Identify the crane and signal person at the start (“Crane 7, this is the hatch”).
- Use short, standard words: “hoist,” “lower,” “stop,” “trolley in,” “trolley out.”
- Many sites use continuous talk during the lift (e.g., “lower, lower, lower… slow… stop”) so that if the radio goes silent, the operator stops.
- Test radios before the lift and carry spare batteries.
- If communication is lost, STOP.
Common mistake: the hatch tender signals “lower” while a lasher on deck waves the operator to “come this way.”
The operator has to guess, and guessing with a 30-ton box overhead is how people get hurt. Establish one signal person before each operation, and everyone else uses only STOP.
Key Takeaway
The qualified signal person is the operator’s eyes. Use one designated signaler at a time, but anyone can call STOP. Learn the ASME standard hand signals exactly. On radio, use a dedicated channel, standard words, and continuous talk; if communication is lost, stop.
With a partner, practice each signal from the table. One person signals, the other calls out the command. Then add radio practice: talk a “load” (a box on a rope) down onto a mark using continuous voice commands, and have the “operator” stop the moment you go silent.
1. Who may give the crane operator a STOP signal?
Anyone may signal STOP or EMERGENCY STOP, and the operator must obey immediately.
2. What does the signal 'both arms extended, palms down, moving back and forth horizontally' mean?
Both arms moving horizontally with palms down is the emergency stop signal.
3. During a radio-directed lift, the radio goes silent. What should the operator do?
Loss of communication means stop until communication is restored.
4. Why should only one designated person give signals during a lift?
Conflicting signals force the operator to guess. One signaler, but anyone can call STOP.