Sling Angles, Center of Gravity, and Load Control
Calculate sling leg tension at different angles, see why low sling angles are dangerous, place the hook over the center of gravity, handle multi-leg and unequal-leg rigging, and control loads with tag lines and edge protection.
Angles Multiply Tension
When sling legs angle out from the hook, each leg carries more than its share of the load. The flatter the angle, the higher the tension.
The Formula
Tension per leg = (load ÷ number of legs) ÷ sin(angle from horizontal)
Or use the load angle factor (1 ÷ sin of the angle):
| Angle from horizontal | Load angle factor |
|---|---|
| 90° (vertical) | 1.000 |
| 60° | 1.155 |
| 45° | 1.414 |
| 30° | 2.000 |
Worked Example
A 10,000 lb load on a two-leg bridle at 45°:
(10,000 ÷ 2) × 1.414 = 7,070 lb per leg
Each sling, shackle, and lifting point must be rated for at least that.
Rules of Thumb
- Keep sling angles at or above 45° from horizontal when possible.
- Avoid angles below 30°. Tension climbs extremely fast, and many standards and companies prohibit them without engineering.
- Use a spreader bar or lifting beam to keep slings vertical on wide loads.
Center of Gravity (CG)
The center of gravity is the balance point of the load. When lifted, a load will swing until its CG is directly below the hook.
- If the hook isn’t over the CG, the load tilts and may shift, slide, or swing into people or structures.
- Determine CG from drawings, markings, or shipping documents (heavy cargo is often stenciled with a CG mark), or by calculation.
- Test lift: raise the load a few inches, check balance and rigging, then continue.
Unequal Legs
When the CG is closer to one lifting point, the shorter / steeper leg nearer the CG carries more of the load. Rigging must be sized for the highest-loaded leg, not an average.
Multi-Leg Slings
With three- or four-leg slings, legs rarely share load equally because of small length differences and rigid loads. A common practice is to assume only two legs carry the load unless an engineer determines otherwise.
Protecting the Rigging
- Edge protection (corner pads, sleeves, wear pads) on sharp edges. Synthetics can be cut through instantly.
- Respect D/d ratio: bending wire rope around a small diameter (a thin pin or sharp corner) reduces its strength.
- Don’t drag slings, and don’t pull slings out from under a resting load.
Controlling the Load
- Tag lines let workers guide and stop rotation from a distance, never by hand on the load.
- Never wrap a tag line around your hand or body.
- Keep clear of pinch points between the load and fixed objects.
- Never stand under a suspended load.
Common mistake: using short slings on a long, wide piece of cargo so the crane has more lift height.
The result is a very flat sling angle, sometimes under 30°, which can double or triple the tension in each leg and overload slings, shackles, and lifting lugs. Use longer slings or a spreader bar.
Key Takeaway
Sling tension = (load ÷ legs) ÷ sin(angle). At 30°, each leg carries double its share. Stay at 45° or more, and use spreader bars for wide loads. Put the hook over the CG, make a test lift, size for the most heavily loaded leg, assume two legs carry multi-leg loads, protect edges, and control the load with tag lines.
A 24,000 lb transformer is lifted with a two-leg bridle at 60° from horizontal.
(24,000 ÷ 2) × 1.155 = 13,860 lb per leg.
If the only available slings make a 30° angle instead, what’s the tension? (24,000 ÷ 2) × 2.000 = 24,000 lb per leg. That’s the entire load in each leg.
1. What is the load angle factor at 30° from horizontal?
1 ÷ sin 30° = 2.0, so each leg carries twice its vertical share.
2. A 6,000 lb load is lifted with two legs at 45°. What's the tension per leg?
(6,000 ÷ 2) × 1.414 ≈ 4,242 lb per leg.
3. Where must the hook be placed relative to the load's center of gravity?
The load swings until its CG is under the hook. Rig it there to keep it level and stable.
4. When rigging a rigid load with a four-leg sling, what's the common conservative assumption?
Small length differences mean legs don't share evenly, so two legs are commonly assumed to carry the load.