Layout and Fitting: Tools and Techniques
Learn what a shipfitter does, from layout with tapes, squares, lasers, and templates to fitting with clamps, dogs and wedges, strongbacks, and jacks, plus tacking, gap and alignment checks, and fairing plate.
What a Shipfitter Does
The shipfitter reads the drawings, lays out where every piece goes, positions plates and shapes, pulls them into alignment, and tack welds them so the welder can make the final welds. A good fit-up makes good welding possible. A bad one can’t be fixed with welding.
- 1 Read
Drawing, member sizes, weld details
- 2 Lay out
Reference lines, member locations
- 3 Position
Crane, chain falls, rigging
- 4 Pull + align
Dogs, wedges, jacks, strongbacks
- 5 Check
Gaps, angles, alignment, level
- 6 Tack
Hold for the welder
Layout Tools
| Tool | Use |
|---|---|
| Tape measure, steel rule | Basic measurements; check tape accuracy |
| Framing square, combination square | Right angles and short layouts |
| Soapstone, paint marker, center punch | Marking lines on steel |
| Chalk line | Long straight lines on plate |
| Levels and plumb bobs | Vertical and horizontal checks |
| Transit, laser level, total station | Long reference lines, heights, block alignment |
| Templates and battens | Curved shapes; fairing curves |
Layout always starts from reference lines (such as the centerline, a frame line, or a deck height above baseline), never from the edge of a plate that might not be square.
Fitting Tools
| Tool | Use |
|---|---|
| C-clamps, pipe clamps, toggle clamps | Holding small parts in position |
| Dogs and wedges | A dog (a small steel bracket tacked to one plate) gives a wedge something to push against to pull plates flush or into line |
| Strongbacks | A stiff beam tacked across a joint to pull plates flat and hold alignment |
| Hydraulic jacks, porta-power | Push members into position with controlled force |
| Come-alongs, chain falls | Pull members into position |
| Fitting bars, pry bars | Fine adjustments |
| Clips and spacers | Set consistent root gaps |
When fitting aids like dogs and strongbacks are removed, their tack welds must be ground flush and inspected (and sometimes tested) so they don’t leave cracks or gouges in the structure.
What to Check Before Handing Over
| Check | Why |
|---|---|
| Root gap within the weld procedure’s range | Too tight = lack of penetration; too wide = excess weld, distortion, burn-through |
| Bevel angle and land correct | Groove geometry controls fusion and penetration |
| Alignment (misalignment / high-low) within tolerance | Offsets concentrate stress and cause fatigue cracks |
| Member location to layout lines | Wrong location means wrong strength or interference |
| Angles and square | Tee members must be at the specified angle |
| Cleanliness | Mill scale, rust, paint, oil, and moisture cause weld defects |
Tack Welds
Tack welds are part of the final weld in many procedures, so they must be:
- Made by a qualified welder with the approved process and filler
- Sound (no cracks); cracked tacks must be removed
- Correct size and spacing, enough to hold but not so large they interfere
- Preheated when the base metal requires preheat
Fairing
Fairing means making plates and members smooth and true, with no bumps, dents, or “hungry horse” waviness between frames. Fitters fair plate using strongbacks, jacks, and, under controlled procedures, heat straightening (line heating). Heat straightening on ship steels must follow the yard’s approved temperature limits, because overheating can change the steel’s properties.
Common mistake: a fitter leaves a gap far wider than the procedure allows, figuring the welder will “fill it up.”
Oversized gaps use far more weld metal, add heat and distortion, risk burn-through, and may not be covered by the weld procedure, which means the weld may be unacceptable no matter how good it looks. Fix the fit, or get an approved repair procedure (such as buttering the edge) before welding.
Key Takeaway
Shipfitters lay out from reference lines, position and pull parts with dogs, wedges, strongbacks, and jacks, check gaps, bevels, and alignment, and tack with approved procedures. Good fit-up makes good welds possible. Remove fitting aids carefully, and fair plate within approved limits.
A butt joint in 1/2-inch plate has a weld procedure calling for a 60° included angle, 1/8-inch root gap (tolerance ±1/16 inch), and maximum misalignment of 1/8 inch.
You measure: angle 60°, gap 1/4 inch, misalignment 1/16 inch.
Is it acceptable? (No. The 1/4-inch gap exceeds the maximum of 3/16 inch. Re-fit the joint or use an approved procedure to correct it before welding.)
1. What is the purpose of dogs and wedges?
A dog tacked to one plate gives a wedge something to push against to pull plates into line.
2. Why should layout start from reference lines rather than plate edges?
Reference lines tie layout to the ship's coordinates. Plate edges can be out of square.
3. What can excessive misalignment (high-low) in a butt joint cause?
Offsets concentrate stress, which can lead to fatigue cracks under cyclic loading.
4. What must be done after removing a temporary fitting aid like a strongback?
Removal areas must be ground and inspected so they don't leave defects in the structure.