Block Construction and Hull Erection
See how modern ships are built in modules, moving from parts to panels to blocks to grand blocks to hull erection, and learn panel lines, pre-outfitting, accuracy control, block alignment, and the erection joint.
Ships Are Built Like Building Blocks
Modern ships aren’t built frame by frame on a slipway. They’re built as blocks (also called modules or units) in shops and staging areas, then lifted into place and joined.
- 1 Parts
CNC-cut plates and shapes
- 2 Sub-assemblies
Webs, brackets, small units
- 3 Panels
Plates + stiffeners on a panel line
- 4 Blocks
3D units: bottoms, sides, decks
- 5 Pre-outfit
Pipe, cable trays, foundations
- 6 Grand blocks
Several blocks joined
- 7 Erection
Lifted into the dock; joined
Why Build This Way?
- Better access: welding in the shop is often downhand (flat), faster and higher quality than overhead work in a finished hull.
- Parallel work: many blocks are built at once.
- Pre-outfitting: installing pipe, cable trays, and equipment foundations in the open block is far easier than in a closed compartment.
- Weather protection: more work happens indoors.
Panel Lines
For flat panels (decks, bulkheads, flat side shell), many yards use a panel line:
- Plates are butt welded into a large flat panel, often by submerged arc welding (SAW) from one side.
- Stiffeners (longitudinals) are positioned and fillet welded, often by automatic gantry welders.
- Webs and other members are added.
Curved shell blocks are built on adjustable pin jigs that hold plates at the correct curvature.
Accuracy Control
Every block must match the blocks around it within tight tolerances. If not, erection joints need cutting, re-fitting, and extra welding, which adds cost and distortion.
Accuracy control includes:
- Shrinkage allowances: parts cut slightly oversize because welding shrinks steel
- Excess stock (extra material) left on some block edges, trimmed at erection
- Dimensional checks with tapes, lasers, and 3D measurement (total stations, laser trackers) at each stage
- Feedback of measurements to adjust future cutting and shrinkage factors
Erection
Blocks are lifted by crane into the building dock or onto the ways, positioned to reference lines (centerline, baseline, frame marks), and supported on blocks and shores.
Fitters then:
- Align the block in all three directions (fore-aft, athwartships, height) and check level and plumb
- Trim excess stock and prepare erection joints (often welded from both sides, or one side with backing)
- Pull plates into alignment with jacks, dogs, and wedges
- Tack, then welders complete the joint following the welding sequence designed to control distortion
Common mistake: a block is out of tolerance, so the crew uses heavy jacks and come-alongs to force it to fit, then welds it.
That locks large residual stresses into the structure, which can cause distortion when nearby welding is done, or cracks later. Report out-of-tolerance blocks so engineering can approve a correction method, and feed the problem back to accuracy control.
Key Takeaway
Ships are built from parts → panels → blocks → grand blocks → erection. Blocks allow downhand welding, parallel work, and pre-outfitting. Accuracy control with shrinkage allowances, excess stock, and 3D measurement keeps blocks fitting together. At erection, align to reference lines, prepare joints, and follow the weld sequence.
You’re building a flat deck block: 4 plates butt-welded together, 10 longitudinal stiffeners, and 2 transverse web frames, plus a pipe penetration and a cable tray.
Order the work. (Example: 1. Butt weld plates on the panel line. 2. Fit and weld longitudinals. 3. Fit and weld web frames. 4. Cut and fit the pipe penetration collar. 5. Install cable tray supports and foundations (pre-outfit). 6. Dimensional check. 7. Paint or prime as specified. 8. Lift to staging.)
1. Why is welding in block construction often done 'downhand'?
Blocks can be turned so most welds are flat, improving productivity and quality.
2. What is pre-outfitting?
Installing outfit items in open blocks is much easier than in closed compartments later.
3. Why are some parts cut slightly oversize?
Welding shrinks steel, so shrinkage allowances keep finished dimensions correct.
4. What's the risk of forcing an out-of-tolerance block into place with heavy jacks?
Forced fits lock in stress. Out-of-tolerance blocks need an engineered correction.