Welding Processes and Positions
Compare SMAW, FCAW, GMAW, GTAW, and SAW and where each is used in shipyards, decode electrode and wire classifications like E7018 and E71T-1, and learn the AWS welding positions 1G through 4G and 1F through 4F.
Arc Welding Basics
Arc welding uses an electric arc between an electrode and the work to melt the base metal and filler metal together. The molten pool must be shielded from the air, or oxygen and nitrogen cause porosity and brittle welds. Processes differ in how they feed filler and shield the pool.
The Main Processes
| Process | Common name | Shielding | Where it shines in a shipyard |
|---|---|---|---|
| SMAW | Stick | Flux coating on the electrode | Repairs, outdoor work, tight spots, all positions; portable |
| FCAW | Flux-core | Flux inside a tubular wire (often plus CO₂ or mixed gas) | The workhorse of most steel shipyards: fast, all-position, tolerant of conditions |
| GMAW | MIG | Shielding gas (Ar/CO₂ mixes) | Thin steel, aluminum (pulsed spray), robotic welding |
| GTAW | TIG | Argon | Pipe roots, stainless, copper-nickel, critical thin work; slow but precise |
| SAW | Sub-arc | Granular flux blanket | Panel lines: long, flat, thick butt and fillet welds; very high deposition |
Other processes you’ll see: electrogas and electroslag for vertical seams on thick side shell, stud welding for insulation pins and fasteners, and friction stir welding for aluminum panels.
DCEP, DCEN, AC
- DCEP (electrode positive, “reverse polarity”): deeper penetration; used for most SMAW and GMAW and many FCAW wires
- DCEN (electrode negative): used for some FCAW self-shielded wires and GTAW of steel
- AC: some stick electrodes and GTAW of aluminum
Always set polarity as the electrode or wire manufacturer and the welding procedure specify.
Decoding Filler Classifications (AWS)
Stick Electrode: E7018
| Part | Meaning |
|---|---|
| E | Electrode |
| 70 | Minimum tensile strength 70 ksi |
| 1 | All positions (a 2 means flat and horizontal only) |
| 8 | Coating type and current: low-hydrogen, iron powder, AC or DCEP |
E7018 is a low-hydrogen electrode, important for avoiding hydrogen cracking in ship steels. It must be kept dry in a rod oven once the can is opened.
Flux-Cored Wire: E71T-1
| Part | Meaning |
|---|---|
| E | Electrode |
| 7 | 70 ksi minimum tensile |
| 1 | All positions (a 0 means flat and horizontal) |
| T | Tubular (flux-cored) |
| -1 | Usability group (here, gas-shielded, typically with CO₂) |
Additional suffixes (like C or M for gas type, and H8 for diffusible hydrogen) appear on many wires.
Solid Wire: ER70S-6
ER = electrode or rod, 70 = 70 ksi, S = solid, 6 = chemistry (extra deoxidizers for welding over light mill scale).
Welding Positions
| Code | Groove (plate) | Fillet |
|---|---|---|
| 1 | 1G Flat | 1F Flat |
| 2 | 2G Horizontal | 2F Horizontal |
| 3 | 3G Vertical (up or down) | 3F Vertical |
| 4 | 4G Overhead | 4F Overhead |
Pipe positions include 5G (horizontal fixed pipe, weld goes around) and 6G (pipe fixed at 45°). A welder qualified in harder positions is often qualified for easier ones too, according to the applicable code.
Shipbuilding involves lots of vertical and overhead welding at erection joints, which is why welder qualifications in 3G and 4G (or 3F and 4F) are valued.
Common mistake: leaving E7018 electrodes out on the deck overnight in humid Northwest air, then using them in the morning.
Low-hydrogen coatings absorb moisture, which puts hydrogen into the weld and can cause delayed cracking hours or days later, especially on higher-strength or thick steel. Store electrodes in a rod oven at the specified temperature, follow exposure limits, and re-bake or discard as the procedure requires.
Key Takeaway
FCAW is the shipyard workhorse; SAW runs panel lines; SMAW handles repairs; GMAW does aluminum and robotics; GTAW does pipe roots and special metals. E7018 = 70 ksi, all-position, low-hydrogen. E71T-1 = 70 ksi, all-position, flux-cored. Positions run 1 (flat) to 4 (overhead), G for groove and F for fillet. Keep low-hydrogen consumables dry.
Pick the most likely process:
- Butt welding 3/4-inch deck plates on a panel line. (SAW.)
- Overhead fillet welds at a block erection joint. (FCAW.)
- Repairing a cracked bracket on a fishing boat at the dock, outdoors, in wind. (SMAW, or self-shielded FCAW.)
- Welding 5083 aluminum superstructure. (GMAW, typically pulsed.)
- Root pass on a copper-nickel seawater pipe. (GTAW.)
1. What does the '1' in E7018 indicate?
The third digit indicates position usability; 1 means all positions.
2. Which process is most common for long, flat butt welds on a panel line?
Submerged arc welding provides very high deposition for long, flat welds.
3. What is the 4G position?
4G is the overhead groove weld position.
4. Why must E7018 electrodes be stored in a rod oven?
Moisture introduces hydrogen into the weld, which can cause delayed cracking.