Hot Work, Fire Watch, and Confined Spaces
Module 5 · Shipyard Safety

Hot Work, Fire Watch, and Confined Spaces

Learn how shipyards control the fire and atmosphere hazards of welding and cutting aboard ships, including OSHA 1915 Subpart B testing, marine chemist certificates, hot work permits, fire watches, oxy-fuel safety, and entering tanks and voids.

Why Ships Are Different

Welding on a ship means working inside steel boxes that once held fuel, cargo, or sewage, with flammable insulation, paint, and wiring on the other side of the plate you’re heating. Fires and explosions during shipyard hot work have killed many workers. The controls exist because of those losses.

In the U.S., shipyard work falls under OSHA 29 CFR Part 1915. Subpart B covers confined and enclosed spaces and other dangerous atmospheres, and Subpart P covers fire protection in shipyard employment.


Testing Before Hot Work

Before hot work in or on certain spaces, especially those that held flammable or combustible liquids or gases (fuel tanks, cargo tanks, pump rooms) and adjacent spaces, the atmosphere must be tested and certified by the right person:

WhoRole
Marine chemistCertified (under NFPA’s marine chemist program) to test and issue certificates for hot work in and around tanks that held flammables, among other situations required by OSHA
Shipyard competent personTrained employee who tests and inspects spaces as allowed by Subpart B, and maintains conditions after a marine chemist’s certificate
Coast Guard authorized personIn some locations where a marine chemist isn’t reasonably available

Marine chemist certificates use standard designations (from NFPA 306), such as:

  • Safe for Workers: oxygen and toxic levels acceptable for entry
  • Safe for Hot Work: flammable vapors below the required limit, and residues cleaned, so welding and cutting can proceed
  • Not Safe for Workers / Not Safe for Hot Work

Conditions can change, so certificates carry conditions and limits, and the competent person re-tests as required, for example after breaks, ventilation changes, or new work.


The Hot Work Permit Process

  1. 1 Test + certify

    Competent person or marine chemist

  2. 2 Clear both sides

    Combustibles removed or protected

  3. 3 Fire watch

    Trained, equipped, in place

  4. 4 Ventilate

    Fumes out; never use oxygen

  5. 5 Hot work

    Within permit limits

  6. 6 Watch after

    At least 30 minutes

Re-test and re-inspect after breaks, shift changes, or any change in conditions.

Fire Watch

A fire watch is a trained person whose only job is to watch for and put out fires during hot work. OSHA Subpart P requires fire watches in specific situations, such as when there’s slag or sparks that could reach combustibles, or heat conducted through bulkheads or decks. The fire watch:

  • Has extinguishing equipment ready and knows how to use it
  • Can communicate with the hot work operator and sound an alarm
  • Watches both sides of the bulkhead or deck being heated, if needed
  • Stays for at least 30 minutes after hot work ends, unless the area is surveyed and determined to have no further fire hazard

Heat Goes Through Steel

Welding or cutting on one side of a bulkhead can heat the other side enough to ignite insulation, paint, wiring, or stored materials. Check the other side before you strike an arc.


Oxy-Fuel Safety

  • Inspect hoses, regulators, and torches; use flashback arrestors.
  • Remove torches and hoses from confined spaces at breaks and at the end of a shift (or disconnect at the supply) so leaking gas can’t accumulate.
  • Never use oxygen to ventilate or “freshen” a space, or to blow off clothing. Oxygen-enriched atmospheres make clothing and materials burn violently.
  • Secure cylinders upright, valves closed when not in use, caps on for transport.

Confined and Enclosed Spaces

Double bottoms, tanks, voids, and cofferdams can be:

  • Oxygen deficient (rust consumes oxygen; inert gas)
  • Toxic (hydrogen sulfide in sewage or fish holds, solvent vapors, welding fumes, carbon monoxide)
  • Flammable (fuel residues)

Never enter a space unless it’s been tested and labeled safe for entry, and follow your yard’s entry and rescue procedures. Most confined space fatalities include would-be rescuers. Don’t go in after someone without proper equipment and a plan.

⚠️ Common Pitfall: 'It Was Safe This Morning'

Common mistake: a tank was certified Safe for Hot Work at 7 a.m., and at 2 p.m. a welder starts cutting after the ventilation was moved for another job.

Conditions change. Vapors can return from residues or adjacent tanks, and ventilation changes affect fumes and oxygen. Check that the certificate and its conditions are still valid, and get the space re-tested when anything changes.


Key Takeaway

Shipyard hot work falls under OSHA 1915. Spaces that held flammables need testing and certification by a marine chemist or competent person (Safe for Workers, Safe for Hot Work). Clear both sides of the work, post a fire watch that stays at least 30 minutes after, remove hoses from confined spaces at breaks, never ventilate with oxygen, and re-test whenever conditions change.

🧪 Try It: Pre-Hot Work Walkdown

You’re assigned to weld a bracket on a bulkhead between an engine room and a fuel tank. List what you’d confirm before striking an arc. (Example: marine chemist certificate covering the fuel tank and the work area, still valid; other side inspected and combustibles removed or protected; fire watch posted on both sides; ventilation and fume control; hot work permit signed; extinguishers in place; hoses and cylinders in good condition.)

🧠 Knowledge Check

1. Which OSHA part covers shipyard employment?

2. What does a 'Safe for Hot Work' designation mean?

3. How long must a fire watch generally remain after hot work ends?

4. Why must you never use oxygen to ventilate a confined space?