Welding Fumes, PPE, and Shipyard Hazards
Module 5 · Shipyard Safety

Welding Fumes, PPE, and Shipyard Hazards

Control welding fume exposures including hexavalent chromium, manganese, zinc, and lead; choose proper PPE and lens shades; and manage electric shock, falls, staging, noise, and heavy lifts in a shipyard.

Welding Fumes

Welding fume is a mix of tiny metal oxide particles and gases. What’s in it depends on the base metal, filler, coatings, and process.

SourceHazard
Stainless steel (and some consumables)Hexavalent chromium, a lung carcinogen. OSHA has a specific chromium (VI) standard for shipyards (1915.1026).
Manganese (in most steel fillers)Nervous system effects with overexposure
Galvanized (zinc-coated) steelZinc oxide fume: metal fume fever (flu-like symptoms)
Old paint on shipsLead (OSHA lead standard for shipyards, 1915.1025), and other toxic coatings
GasesOzone (from GMAW/GTAW arcs), carbon monoxide (especially CO₂-shielded processes in confined spaces), nitrogen oxides
Shielding gasesArgon and CO₂ displace oxygen in low or enclosed spaces

Controls, in Order

  1. Remove coatings from the weld area before welding where possible (using safe methods for the coating).
  2. Local exhaust ventilation: fume extractors and fume-extracting guns placed near the arc.
  3. General ventilation in enclosed spaces (blowers, exhaust trunks).
  4. Respiratory protection where ventilation isn’t enough, under a respiratory protection program with fit testing.
  5. Position your head out of the fume plume.

Personal Protective Equipment

HazardPPE
Arc radiation (UV, IR), spatterWelding helmet with the correct shade lens, safety glasses underneath
BurnsFlame-resistant clothing (wool or treated cotton; avoid synthetics that melt), leather gloves, jacket or sleeves, boots
Cutting and grindingFace shield over safety glasses, hearing protection
NoiseEarplugs or muffs; arc gouging and grinding are very loud
FumesRespirator when required
Falling objectsHard hat (under or compatible with the welding helmet)

Lens Shade

Use the shade recommended for your process and amperage (references such as ANSI Z49.1 and lens makers publish charts). As a rough guide, many arc welding tasks use roughly shade 10 to 13, with higher shades at higher currents. Arc gouging and high-amperage work need darker shades. Auto-darkening helmets must be the right shade and kept working.

Protect bystanders with welding screens, because arc flash (“welder’s flash”) burns the eyes of anyone nearby.


Electric Shock

Ships are steel, often wet, and frequently cramped, a perfect setup for electric shock.

  • Inspect leads and electrode holders for damaged insulation.
  • Keep dry gloves and clothing; don’t lie on wet steel without insulation.
  • Make a solid work lead connection close to the weld, so current doesn’t wander through the hull, piping, bearings, or other machinery (stray current can damage equipment).
  • In tight or wet locations, use machines with voltage-reducing devices where required.
  • Never change electrodes with bare or wet hands.

Falls, Staging, and Openings

Hull work means staging (scaffolds), open hatches, tank openings, and work at height on the dock floor or ship’s side.

  • Use guardrails or fall protection where required.
  • Inspect staging before use; a competent person signs off on erection and changes.
  • Cover or guard deck openings and manholes.
  • Keep housekeeping tight: leads, hoses, and scrap are trip hazards.

Heavy Lifts and Moving Loads

Plates, shapes, and entire blocks move overhead by crane every day. Stay out from under suspended loads, follow the signal person, and use tag lines (see the Port and Crane Operations course for rigging and signals).

⚠️ Common Pitfall: Welding Galvanized Without Ventilation

Common mistake: welding galvanized railings or brackets in a small compartment “just for a few minutes.”

Zinc fume causes metal fume fever: chills, fever, and nausea a few hours later. Remove the galvanizing from the weld area where allowed, use local exhaust, and wear a respirator when needed. If you feel sick after welding galvanized steel, report it.


Key Takeaway

Fumes vary by metal and coating: hexavalent chromium from stainless, manganese from steel fillers, zinc from galvanizing, lead from old paint. Control them with coating removal, local exhaust, ventilation, and respirators. Wear FR clothing, the right lens shade, and protect bystanders. Prevent shock on wet steel, guard falls and openings, and stay clear of suspended loads.

🧪 Try It: Hazard Hunt

For each task, list the main hazards and controls:

  1. Stick welding inside a wet double-bottom tank. (Shock, fumes, oxygen-deficiency or confined-space hazards, heat. Controls: tested space, ventilation, dry insulating mats, intact leads, voltage-reducing device, attendant.)
  2. Cutting old painted steel during a ship repair. (Lead and toxic paint fumes, fire. Controls: test the paint, strip it, exhaust, respirator, fire watch.)
  3. TIG welding stainless pipe. (Hexavalent chromium, UV, ozone. Controls: local exhaust, respirator if needed, correct shade, covered skin.)
🧠 Knowledge Check

1. Welding stainless steel can produce which carcinogenic fume?

2. What causes metal fume fever?

3. Why place the work lead close to the weld?

4. Which clothing is best for welding?